A 4-to-6-inch turbo blade spends most of its working life mounted on an angle grinder, cutting sink radii, trimming overhangs, or squaring a rough edge before a bridge saw ever touches the piece. For hard, abrasive material — granite, quartzite, the resin-bound surface of engineered stone — the rim pattern on that blade decides whether the cut finishes clean or whether the fabricator spends the next ten minutes grinding out chatter marks. The Diamax Cyclone S Arrowtek Turbo Blade is built around a rim geometry Diamax calls Arrowtek, sold in 5, 5.5 and 6 inch diameters (SKUs TBA50, TBA55 and TBA60) for exactly that kind of hand work.
This spotlight checks every spec against the manufacturer rather than repeating the store page as written, because the store page is not internally consistent: its feature line names granite and quartzite, while its own specification table lists "Engineered Stone, Concrete" as the compatible material. Diamax's own product listing resolves that in favor of granite, quartzite and engineered stone — concrete does not appear anywhere in the manufacturer's material list for this blade, and that is the figure used throughout this article. The segment dimensions, arbor, bushing and the RPM rating for each of the three sizes are confirmed the same way, against the manufacturer's own page and a second independent stone-tooling retailer's spec table that matches it line for line.

What a Turbo Rim Does, and Where Arrowtek Fits
Diamond blade rims fall into three broad families, and the differences are mechanical, not marketing. A continuous rim is a smooth, uninterrupted band of diamond with no gaps; it cuts slowly but leaves the cleanest edge, which is why it is the default choice for tile, porcelain and other brittle, delicate materials that chip easily. A segmented rim has visible gullets — slots cut between individual diamond segments — that clear debris and dissipate heat aggressively, which lets it cut fast through concrete and masonry at the cost of a rougher edge. A turbo rim sits between the two: a serrated or notched rim with small gaps rather than full gullets, giving most of the speed of a segmented blade with a finish much closer to a continuous rim.
That middle position is also why turbo blades are rated for both wet and dry cutting in a way continuous rims generally are not. The small notches around a turbo rim still move enough water or air past the cutting face to manage heat, while a smooth continuous rim depends on a steady water feed to avoid overheating the bond and glazing the diamond. For a fabricator working a sink cutout or an edge trim with a hand-held grinder rather than a wet saw, that dry-capable design is often the entire reason to reach for a turbo blade instead of a continuous one.
Arrowtek is Diamax's name for the specific notch pattern cut into this blade's rim. Diamax's own description states only that the Arrowtek rim lets the blade "cut faster and cleaner than traditional turbo blades on hard materials" — the manufacturer does not publish a separate engineering explanation of the geometry beyond that claim, and nothing beyond it is stated here. What can be confirmed independently is the category: Arrowtek is a turbo-family rim, not a segmented or continuous one, so it inherits the wet-or-dry flexibility and the speed-versus-finish balance of that family, with Diamax's pattern aimed specifically at hard, abrasive stone rather than general masonry.
For a shop that already stocks a standard turbo blade, the question is whether Arrowtek's hard-stone focus is worth a second SKU on the bench. The honest answer is that it depends on the mix of material coming through the shop: a fabricator cutting mostly granite and quartzite benefits from a rim built for that material, while a shop splitting its time between stone and concrete block or paver work is better served by a general-purpose turbo blade that is not optimized away from its own most common job.
Running the Cyclone S Arrowtek in the Shop
Sizes, Segments and Mounting
All three sizes share the same segment and arbor specification, which simplifies stocking: the diamond segment measures 8 mm wide by 2.4 mm high on every size, and the arbor is a combination 5/8 inch, 7/8 inch, 20 mm bore with bushing BS57820S, so the same blade mounts on a small angle grinder spindle or steps down with the bushing to fit a hand saw. The only variable across the line is diameter and the resulting maximum RPM rating, which is why checking the plate on the tool before fitting any of the three sizes matters more than it would on a single-size blade.
The table below lines up the Arrowtek's confirmed, manufacturer-sourced numbers against the three rim families in general terms. Only the Arrowtek row carries specific figures; the other rows describe the category the way the broader diamond-tooling trade does, without borrowing numbers that belong to a different blade.
| Rim type | Rim design | Speed vs. finish | Typical use |
|---|---|---|---|
| Diamax Cyclone S Arrowtek (TBA50 / TBA55 / TBA60) | Arrowtek-pattern turbo rim; segment 8 mm x 2.4 mm; arbor 5/8"-7/8"-20 mm with bushing BS57820S | Max RPM 12,000 (5"), 10,185 (5.5" and 6") | Granite, quartzite, engineered stone; angle grinder or hand saw, wet or dry |
| Standard turbo rim | Serrated continuous rim with small notches, no full gullets | Faster than continuous, cleaner than segmented | General stone and masonry hand work, wet or dry |
| Segmented rim | Visible gullets between diamond segments | Fastest, most aggressive; rougher edge | Concrete, block, heavy-duty demolition cutting |
| Continuous rim | Smooth, uninterrupted diamond band | Slowest; cleanest, chip-free edge | Tile, porcelain, delicate decorative stone, mainly wet |
Wet vs. Dry, and Matching Grinder RPM to the Blade
Diamax rates this blade for both wet and dry cutting, so the choice between them comes down to the job rather than the tool. Dry cutting is the practical default for a sink cutout or an edge trim on an installed or near-finished piece where flooding the area with water is not an option; wet cutting, even just a drip feed from a bottle, extends segment life and keeps dust down on longer cuts. What is not optional is matching the grinder's maximum RPM to the blade's rating for the size in hand — running a 5-inch Arrowtek rated to 12,000 RPM on a grinder that exceeds that figure overloads the blade well beyond its design margin, and the 5.5 and 6 inch sizes drop to a lower 10,185 RPM ceiling precisely because the larger diameter spins the rim's outer edge faster at the same angular speed.
Checking that number before the first cut is a five-second habit that prevents a blade failure most fabricators only make once. Grinders sold specifically for stone work typically print their no-load RPM on the housing or the spec label, and that figure should sit at or below the blade's rating for the diameter actually mounted, not the rating for a different size in the same product line.
Break-In and Dressing
A new turbo-rim blade almost always cuts slower for the first few passes than it will once it has worn in, because the bond around the outermost diamond layer has not yet been exposed. A short break-in on a scrap offcut of the same material — granite or quartzite, not a softer stone that will glaze the rim instead of opening it — brings the blade to full cutting speed faster than pushing it straight into a production cut. If cutting speed drops off later in the blade's life even though diamond is still visible around the rim, that is almost always a bond that has glazed from heat rather than a blade that has run out of diamond; a few light passes against an abrasive dressing stick re-exposes fresh diamond and restores the cut without replacing the blade.
Spotlight: The Diamax Cyclone S Arrowtek Turbo Blade ships in 5, 5.5 and 6 inch sizes for angle grinders and hand saws. Diamax's own listing rates it for granite, quartzite and engineered stone — not concrete, despite what the store's own spec table says — at up to 12,000 RPM on the 5 inch size and 10,185 RPM on the 5.5 and 6 inch sizes, wet or dry.
Where This Blade Wins, and Where a Different Diamax Blade Wins Instead
The Arrowtek earns its spot on the bench for the jobs a turbo rim is built for: trimming an overhang to a scribed line, cleaning up a rough bridge-saw edge, taking down a sink cutout corner, or putting a quick chamfer on a piece before it ships. Its hard-stone focus makes it a better default for a shop that is cutting granite and quartzite most days than a general turbo blade optimized for a wider, softer material range.
It is not the right choice for every job in that size range, though, and two other blades in the same Diamax Cyclone line cover the gaps. The Diamax Cyclone Side Segment turbo blade is built around side-mounted segments rather than a turbo rim, trading some of the Arrowtek's finish for extra aggression on straight granite cutting where speed matters more than a polished edge. For quartzite specifically pushed to a bridge saw rather than a hand grinder, the Diamax Cyclone QZT blade is engineered around that stone's higher silica content and abrasiveness in a way a hand-held turbo blade, Arrowtek included, is not designed to match on volume production cuts.
A fabricator stocking all three is not duplicating inventory; each blade is answering a different question. The Arrowtek answers "which hand-held blade do I reach for on hard stone," the Side Segment answers "which blade cuts granite fastest on a hand saw when the edge will be ground afterward anyway," and the QZT answers "which bridge-saw blade survives a full day of quartzite." Mixing them up — running the Side Segment where a clean edge is needed, or expecting a hand-held Arrowtek to do a bridge saw's job — is the more common mistake than any failure in the blades themselves.
A broader comparison of 4 to 6 inch turbo blades across brands, not limited to the Diamax line, is covered in Turbo Blades for Stone: Choosing the Right 4"-6" Blade; that article is the place to start for a fabricator who has not yet settled on turbo blades as the right category at all, while this spotlight assumes that decision is already made and focuses on one specific blade within it.
Keeping an Arrowtek Blade Cutting True Over Its Life
A turbo blade's working life is largely a function of how much heat it absorbs relative to how much of that heat gets carried away. Dry cutting in long, continuous passes is the fastest way to shorten a blade's life, because the rim has no water to carry heat off the bond between passes; breaking a long dry cut into shorter strokes with brief pauses lets the small gaps in the Arrowtek rim do the cooling job they are designed for instead of fighting a constant heat load.
Storage matters almost as much as use. A diamond blade left in a damp toolbox or exposed to temperature swings on a job site can develop rust at the steel core, and rust under the segments is one of the more common causes of a segment letting go in use rather than wearing down evenly. Keeping the blade dry between jobs and wiping down the core before it goes back in a case is a cheap habit against an expensive failure mode.
Watch the segment height, not just the overall diameter, as the real gauge of remaining life. A turbo rim that has worn down close to the steel core cuts slower and runs hotter for the same feed pressure, which is often misread as a dull blade needing replacement when a quick dressing pass would restore most of the lost performance. Replacing a blade purely on a mileage estimate, without checking whether the diamond is actually gone, wastes tooling budget that would be better spent on consumables that are genuinely worn out.
Finally, match the blade to the arbor correctly every time it is remounted. The 5/8 inch, 7/8 inch, 20 mm combination arbor with the BS57820S bushing is designed to seat securely across several common grinder and saw spindle sizes, but a bushing that is not fully seated, or a blade mounted without the correct washer, is a far more common cause of wobble and premature wear than any defect in the blade itself. A blade that runs out of true wears unevenly around the rim long before it runs out of diamond.
None of this is unique to the Arrowtek specifically — it is standard turbo-blade discipline that applies across the Diamax Cyclone line and most hard-stone turbo blades from other manufacturers. What is specific to this blade is the RPM ceiling for each of its three sizes, and that figure is worth writing on a shop's grinder log rather than trusting to memory, especially in a shop that keeps more than one size of Arrowtek on hand.
Fabricators comparing the Arrowtek against the rest of the Diamax Cyclone family, or sourcing a replacement for a different diameter, can browse the full diamond blades collection alongside the Cyclone S Arrowtek product page itself for current sizes and variant SKUs.
Free Tool
Diamond Blade Selector — answer a few questions about the stone, the machine and the cut you need, and get a shortlist of the right blades and core bits for the job instead of guessing from a product title.
Find Your Blade →Stock the Right Turbo Blade for Hard Stone
Browse the Diamax Cyclone S Arrowtek in 5, 5.5 and 6 inch sizes alongside the full diamond blade lineup.
Shop Diamond Blades →