CounterBalance IslandBar Overhang Support 24" (Box of 3)
Recogida disponible en Dynamic Stone Tools Warehouse (Sterling, VA)
Normalmente está listo en 2 horas
CounterBalance IslandBar Overhang Support 24" (Box of 3)
Descripción
Descripción
CounterBalance IslandBar 24 in Hidden Island Support Bracket
The CounterBalance IslandBar (24 in) is a concealed steel island support bracket for countertop overhangs on a kitchen island or breakfast bar off of cabinetry. It attaches to the side walls of the cabinetry and supports overhangs of up to 18 in (457 mm) on 3 cm stone. This listing is a box of 3 brackets.
Features
- Concealed steel island support bracket for stone and solid surface countertop overhangs
- Supports overhangs of up to 18 in (457 mm) on 3 cm stone
- Attaches to the left or right cabinet wall, supporting island and peninsula countertops above cabinetry
- Low-profile bracket hidden from view for a clean, modern look
- Alternative to pricey corbels, which customers can bang their knees on
- Notch that aids installation when installed at full length
- Can be installed further back into the cabinet to accommodate overhangs shorter than 15 in (381 mm)
- Box of 3 brackets, each 24 in (610 mm) long
- Select locations for the IslandBars, spaced no more than 16–20 in (406–508 mm) apart for optimum performance.
- Position the IslandBar on the cabinet so the edge of the bracket will sit 3–6 in (76–152 mm) back from the edge of the counter surface once installed, and scribe a line on the cabinet wall just behind the rear edge of the bracket.
- Using a router with a 1/4 in (6.4 mm) bit, route the top of the cabinet to the line at 3/16 in (4.8 mm) depth so the IslandBar sits flush on the cabinet.
- Trace the T profile of the bracket onto the face of the cabinet and mask the surrounding area.
- Using a circular saw or oscillating multitool, cut out the marked area and test fit the bracket as necessary.
- Place the IslandBar onto the top of the routed cabinet, mark the point in each slot to be drilled, then remove the bracket.
- Drill the holes, place the IslandBar back into position and attach it with screws. Repeat as necessary and set the top position.
- Apply a silicone sealant to the top of the IslandBar to secure it to the underside of the counter surface and set the countertop into position.
| Property | Detail |
|---|---|
| Brand | CounterBalance |
| Model | IslandBar (24 in) |
| Material | Steel |
| Length | 24 in (610 mm) |
| Pack | Box of 3 |
| Maximum Overhang | 18 in (457 mm) on 3 cm stone |
| Recommended Spacing | No more than 16–20 in (406–508 mm) apart |
| Mounting | Attaches to the left or right cabinet wall |
| Countertop Types | Stone and solid surface |
How far can an overhang extend with the IslandBar?
Chemical Concepts states that the 24 in IslandBar supports up to 18 in (457 mm) overhangs on 3 cm stone. The shorter IslandBar Mini supports 15 in (381 mm) overhangs.
How far apart should the supports be spaced?
Chemical Concepts states that supports should be spaced no more than 16 to 20 in (406 to 508 mm) apart for optimum performance.
Does it need a professional installer?
The installation instructions say to consult a professional when installing brackets for a load-bearing application, to be sure the bracket has a substructure able to support it and any additional weight, and to consult a professional installer when in doubt.
⚠ WARNING: Cancer and Reproductive Harm — www.P65Warnings.ca.gov. Always wear appropriate PPE.
