Same-Day Shipping Before 12 PM ET | Call 703-957-4544

Check out our brands. MAXAW, KRATOS, RAX and more. Learn more

Stonify, our Official Tech Partner for Fabricators. Book a free demo

Akemi Polishing Fluid No. 10: A Wax and Resin Stone Polish Spotlight

Akemi Polishing Fluid No. 10: A Wax and Resin Stone Polish Spotlight

Dynamic Stone Tools

Every restoration crew and every fabricator who installs interior stone eventually gets the same call: a marble foyer, a run of travertine stair treads or a set of granite window sills that looks flat and washed out even though the surface has been cleaned. Sometimes the answer is a full re-hone and re-polish with diamond abrasives. Often, though, the stone has a sound fine-ground or polished finish already, and what the client is really missing is depth of color and a cared-for sheen. That is the niche a solvent-borne wax and resin care product is built for, and it is exactly where Akemi Polishing Fluid No. 10-2012 sits.

This spotlight walks through what the product is according to Akemi's own technical data sheet and the Dynamic Stone Tools listing, where it belongs on a job and where it does not, how to apply it so the film buffs out instead of smearing, and how to store a liter so it is still usable next season. Every number quoted below comes from Akemi's published data or the product specifications. Read it as a field guide for using a care product correctly, not as a substitute for mechanical polishing.

Akemi Polishing Fluid No. 10-2012 1 L wax and resin stone polish

What Polishing Fluid No. 10-2012 Is and Where It Fits

Akemi describes Polishing Fluid No. 10-2012 as a fast-drying, solvent-based product made from high-quality waxes and synthetic resins. The manufacturer's data sheet states that the carrier is a hydrocarbon solvent, and Akemi's product page adds that the formula is free of trichloroethylene and chlorinated hydrocarbons. In plain terms, it is a liquid that lays down a thin wax and resin film once the solvent flashes off. That film is what you buff to bring up sheen, and it is also what deepens the color of the stone underneath, which is why the product is marketed as a color-intensifying polish rather than as a clear protective coating alone.

It helps to be precise about the category, because fabricators sometimes lump every bottle on the chemical shelf together. A penetrating impregnator is designed to soak into the pores of the stone and leave little or nothing on top. A wax and resin care product like No. 10-2012 works mostly at the surface: it fills the micro-texture of a fine-ground face, evens out how light reflects off it and gives the surface a renewable layer that takes the scuffing instead of the stone. That makes it a maintenance and finishing product. It does not replace the grit sequence that creates a polish in the first place, and it is not sold as a stain-blocking treatment for kitchen work surfaces.

According to Akemi, the intended field of application is interior care of floors, stairs and window sills made of fine-ground or polished natural and artificial stone, and the data sheet names marble, granite, slate, terrazzo and travertine as examples. Akemi's product finder also lists limestone and cotto among suitable materials, along with surfaces described as fine-ground, satinated, antique and polished. The common thread is a dense, already-refined interior surface that sees foot traffic or hand contact and benefits from a renewable sheen. The Dynamic Stone Tools listing summarizes the result as a brilliant, anti-slip finish that intensifies the stone's color.

The anti-slip point deserves attention because floors and stairs are the main targets. Akemi's data sheet describes the finish as slip-resistant, and that matters: a care product applied to stair treads that turned them slick would be a liability rather than an upgrade. The manufacturer does not publish a slip-resistance test value for this product, so do not quote one to a customer. If a commercial client needs a documented slip rating for a floor, that is a separate conversation, and the stone should be tested in its finished condition rather than assumed to meet a number on the strength of a product description.

Applying Polishing Fluid No. 10: Prep, Thin Coats and Buff-Out

Most complaints about wax and resin polishes trace back to application rather than to the product. A streaky, tacky or cloudy result almost always means the surface was not fully clean and dry, the coat was too heavy, or the buffing happened at the wrong moment. Akemi's instructions are short, and following them exactly is what separates a crisp, even sheen from a film that has to be stripped and redone. The sections below follow the order of the data sheet and add shop context around each step.

Surface Preparation

Akemi specifies cleaning the surface thoroughly with Akemi Stone Cleaner before application, and the data sheet is explicit that the surface must be clean and completely dry. Any residue left behind, whether it is soil, an old soap film or slurry from honing, gets locked under the new wax and resin layer and shows as haze. On a restoration job that means cleaning, rinsing and then giving the stone enough time to dry out before the fluid goes down. Dense polished granite dries quickly; a porous, freshly washed travertine or limestone may need considerably longer, so plan the schedule around drying rather than around the clock.

Temperature and Working Conditions

The data sheet gives an optimal application temperature of 15–25°C, which the Dynamic Stone Tools listing converts to 59–77°F. That range covers the stone and the room, not just the bottle. Akemi also warns that the fluid thickens below 9°C and becomes nearly solid below 0°C, and that cold-stored product should rest at about 15°C before use. Because the carrier is a solvent, Akemi tells users to protect solvent-sensitive items in the work area, naming certain plastics, rubber and painted surfaces. On window sills that means masking vinyl frames, gaskets and painted trim before the first wipe.

Coating and Buffing

Apply a thin coat with a cloth or brush, or with a mop on larger floor areas. On very absorbent, unpolished surfaces Akemi calls for several coats, because the first pass is partly drawn into the stone. The single most important instruction is the warning that only thin coats should be applied, since thick coats lead to poor polishability. Once the treated surface turns matte, buff it with a soft cloth or with a white nylon pad on a single-disc machine. Buffing too early drags wet film around; waiting for the matte stage lets the waxes and resins set enough to take a sheen.

Property Detail (per Akemi data / product listing)
Chemistry Waxes and synthetic resins in a hydrocarbon solvent; fast-drying
Finish Brilliant, slip-resistant; intensifies stone color
Suitable stone Fine-ground or polished natural and cast stone: marble, granite, slate, terrazzo, travertine
Use location Interior floors, stairs, window sills
Application temperature 15–25°C (59–77°F)
Coverage Approx. 15–30 m² per liter (about 160–320 sq ft)
Color / density Slightly yellowish liquid; approx. 0.75 g/cm³
Cold behavior Thickens below 9°C; rest at about 15°C to restore
Storage / shelf life Cool, frost-free, sealed; 2 years per listing
Container 1 L (33.8 fl oz)

Estimating Material for a Job

Akemi rates coverage at approximately 15–30 square meters per liter, roughly 160 to 320 square feet. The spread is wide for a reason: a dense polished granite floor sits at the high end, while an absorbent honed surface that needs multiple coats pulls toward the low end. For quoting, measure the area, assume the conservative figure for porous or unpolished stone, and add the number of coats you expect. A 1 L bottle is plenty for a set of sills or a small powder-room floor; a large foyer or a long stair run may call for several. Doing a test section first gives a real consumption figure for that specific stone.

Spotlight: Akemi Polishing Fluid No. 10-2012 (1 L) is a fast-hardening, solvent-borne wax and synthetic resin polish for interior fine-ground or polished natural and cast stone. It intensifies color, leaves an anti-slip sheen, covers approximately 15–30 m² per liter and applies by cloth, brush or mop before buffing with a soft cloth or white nylon pad. Keep coats thin and work at 15–25°C for the best result.

Field Tips for Fabricators and Restoration Crews

Window sills are the natural shop application. Sills are usually fabricated, edged and polished in the shop, then installed after the window trades are finished. A thin coat of No. 10-2012 on the finished face and exposed edge, buffed out before crating, delivers a piece with deeper color on arrival. Because Akemi warns about solvent-sensitive plastics and painted surfaces, treating sills in the shop before installation avoids the problem of the fluid touching a vinyl frame or freshly painted jamb on site. If sills are treated after installation, mask carefully and use a cloth rather than a brush to keep the product where it belongs.

Stair treads and landings are the second obvious target, and they reward a methodical approach. Clean and dry the whole run first, then coat every other tread so the stairs remain usable while the alternate steps flash off and get buffed. Hand-buff nosings and edges, where a machine pad will not reach evenly. The anti-slip character of the finish is a selling point here, but the safe practice is still to keep foot traffic off a tread until it has been buffed and has had time to set, and to tell the client how long the stairs will be out of service before you start.

Always run a test patch. Akemi's own data sheet states that its information is guidance and that users should conduct their own tests on an inconspicuous area before full application. That instruction carries extra weight with a color-intensifying product: the darkening that makes a dull granite look rich can also change the look of a pale marble or a light limestone more than a client expects. Treat a closet corner, the underside of a sill offcut or a remnant of the same slab, buff it, and let the client approve the look in daylight before you commit to the whole floor.

Match the product to the condition of the surface. No. 10-2012 is meant for surfaces that are already fine-ground or polished; it refines and protects that finish but will not erase scratches, etch marks or lippage. If a marble floor is etched, dull in traffic lanes or scratched, the correct sequence is mechanical work first, honing and polishing with diamond abrasives or a polishing compound, and then a care product on top. Putting wax over a damaged surface simply seals the damage under a shiny film. Assess the floor under raking light before quoting so the client pays for the right scope.

Keep the use interior. Akemi's data sheet and the product listing both limit the product to indoor surfaces, and the solvent-borne wax film is a care layer rather than a weathering treatment. For exterior paving, pool surrounds or facades, choose a product that the manufacturer explicitly rates for outdoor exposure. Likewise, for kitchen countertops and food-contact areas, select products whose documentation addresses that use; this fluid is described for floors, stairs and sills, and staying within the stated application keeps both the result and your liability position clean.

Maintenance, Storage and Long-Term Considerations

One of the practical advantages Akemi lists for this product is that the treated surface can be polished up and renewed as required. A wax and resin film wears gradually in traffic lanes rather than failing all at once, so the usual maintenance cycle is light cleaning plus an occasional fresh thin coat buffed into worn areas. Keep the renewal coats as thin as the first one; repeated heavy applications are how a floor ends up with a yellowed, gummy build-up that has to be removed before anything else can be done.

When build-up does happen, or when a client wants a different finish, the film has to come off. Akemi's data sheet notes that layers of stone-care products can be removed with an Akemi solvent product, and Dynamic Stone Tools carries the Akemi Wax Stripper, sold as a solvent-based wax, tar and coating remover for natural and artificial stone. Strip, rinse according to that product's instructions, let the stone dry completely and only then decide whether to reapply. Skipping the dry-out step after stripping is the most common reason a fresh coat goes down cloudy.

Storage is straightforward if you respect the temperature notes. Akemi specifies storing the product in a dry, cool place in its original sealed container, and the Dynamic Stone Tools listing gives a shelf life of two years when kept cool, frost-free and sealed. In practice the risk is the service truck in winter. A bottle left in an unheated van can thicken past usefulness; if that happens, Akemi's guidance is to let it rest at about 15°C before use. Bring partly used bottles indoors, tighten the cap fully so the solvent does not evaporate, and date each bottle when opened.

Protect the people as well as the stone. Akemi recommends its afin Liquid Glove barrier cream for hand protection during application, and Dynamic Stone Tools stocks Akemi Liquid Glove for exactly that purpose. Because the carrier is a hydrocarbon solvent, read the Safety Data Sheet before use, ventilate interior rooms, keep ignition sources away and follow the manufacturer's PPE guidance. Akemi labels the product for professional use, which is another reason to keep it in the hands of trained crews rather than leaving a bottle with the homeowner for touch-ups.

To build a complete interior care kit around this product, pair it with Akemi Stone Cleaner for the mandatory pre-clean, Akemi Liquid Glove for hand protection and the Akemi Wax Stripper for removing old coatings. Shops comparing finishes may also want to look at Akemi Solid Wax, the Akemi Colour Intensifier for a wet-look enhancement and Akemi Liqui Polish Universal, a polishing compound for mechanical refinishing before any care product goes on. You can find the fluid itself on the Akemi Polishing Fluid No. 10-2012 product page.

Free Tool

Free Guides & Tools — Browse the Dynamic Stone Tools hub of free guides and tools to plan stone care, finishing and restoration jobs like the ones in this spotlight.

Explore Free Guides & Tools →

Stock Your Stone Care Shelf

Dynamic Stone Tools carries Akemi cleaners, waxes, polishes and strippers for fabricators and restoration crews. Order the products your interior care jobs need and get them on the truck.

Shop Stone Care Products →
Previous Next

Leave a comment

Please note: comments must be approved before they are published.