Envío el mismo día antes de las 12 PM ET | Llame al 703-957-4544

Echa un vistazo a nuestras marcas. MAXAW, KRATOS, RAX y más. Más información

Stonify, our Official Tech Partner for Fabricators. Book a free demo

Weha T300 UNI-PAD: A Pneumatic Vacuum Lifter Spotlight

Weha T300 UNI-PAD: A Pneumatic Vacuum Lifter Spotlight

Dynamic Stone Tools

Moving stone is where many fabrication shops lose the most time and take the most risk. Sawn pieces, sink-cutout tops, backsplash strips and vanity blanks all need to travel from the saw to the bench, from the bench to the edge line, and from the edge line onto carts or A-frames. Doing that by hand with a team of people strains backs and invites dropped edges, while chaining up every small piece with clamps is slow. A single-pad vacuum lifter hung from an overhead hoist sits right in the middle of those options, and it changes how a shop handles its everyday medium-weight pieces.

The Weha T300 UNI-PAD is one of those lifters, and its name deserves a quick clarification. Despite the polishing-pad wording that sometimes travels with the product, the T300 UNI-PAD is a pneumatic, air-only vacuum lifter: the UNI-PAD is its suction pad, not a diamond polishing disc. According to the Tenax USA product page, which the manufacturer documentation on our listing points to, it uses a compressed-air venturi system with no electrical power required. In this spotlight we look at its published specifications, how it fits into a fabrication workflow, the daily checks that keep vacuum lifting safe, and how to look after the pad and air system.

Weha T300 UNI-PAD pneumatic vacuum lifter

How an Air-Only Vacuum Lifter Holds Stone

A vacuum lifter works by pulling air out from under a sealed pad pressed against a flat surface. Once the pressure under the pad drops below the surrounding atmosphere, the outside air presses the pad and the stone together, and the lifter can raise the piece from above. The quality of the seal between pad and stone, the area of the pad, and the vacuum level the system reaches together determine how securely a load is held. That is why flatness, cleanliness and pad condition matter as much as the rated capacity printed on the nameplate.

The T300 generates its vacuum with a venturi. Instead of an electric pump, compressed air from a shop compressor flows through a shaped passage, and that flow creates suction at the pad. Tenax lists the air requirement as a minimum of 60 PSI at 2 CFM, which it describes as achievable with a small compressor, and notes that no electrical power is required. For a fabrication shop that already runs pneumatic tools, that means the lifter can work from an existing air drop rather than needing its own power cable running up to the hoist.

The UNI-PAD itself is the suction plate. Tenax gives its size as 21.3 inches by 6 inches and says it works on both polished and rough surfaces, with rubber seals that are quick to replace to keep maintenance costs down. A long, narrow plate like this suits the shapes fabricators handle constantly: countertop sections, backsplash strips, sills and similar pieces where a round cup would grip only a small portion of the width. The listing also names granite, marble, natural stone, engineered stone and quartz, glass and metal panels among suitable materials.

Safety in a vacuum lifter comes from redundancy and visibility. Tenax describes a built-in, non-corrosive aluminum safety vacuum tank on the T300, a highly visible pressure gauge, and a multi-filter with water trap to keep dust and moisture out of the pneumatic components. On its own site, Weha explains the purpose of a vacuum safety tank on its larger UNI-PAD lifters: if pressure is lost, the stored vacuum allows the panel to be set down safely. The gauge, meanwhile, lets the operator confirm the vacuum level before the load ever leaves the table.

Why does this matter for a shop owner weighing equipment purchases? Because handling is a cost center that rarely shows up on a quote. Every piece of stone in a shop gets lifted several times before it leaves, and every lift done by hand takes people away from cutting and finishing. A properly rated, well-maintained vacuum lifter can reduce the number of people needed for routine moves, keeps hands off polished faces and edges, and makes the move itself more repeatable, which is the foundation of a safer and more productive floor.

Putting the T300 to Work in the Shop

The published specifications define where the T300 fits. The table below collects them from the Tenax USA product page, the manufacturer documentation linked from our listing. Use them as a starting point, and always confirm against the nameplate and instruction manual that come with your unit, since those govern the actual rating of the lifter in your hands. After the table, we walk through the practical steps of setting up and using the lifter, from air supply to the moment the stone touches down on the bench.

Specification Published value (Tenax USA)
Type Pneumatic vacuum lifter, air-only venturi system
Horizontal load capacity 661 lbs
Vertical load capacity 331 lbs
Suction plate (UNI-PAD) 21.3 in x 6 in
Unit weight 33 lbs
Air requirement Minimum 60 PSI at 2 CFM
Safety features Aluminum safety vacuum tank, pressure gauge, multi-filter and water trap
Manufacturer part number 8010296 (per our product listing)

Reading the Capacity Numbers

Two capacities are listed: 661 lbs horizontal and 331 lbs vertical. Converted to metric, 661 lbs is about 300 kg, which matches the number in the model name, and the vertical figure is roughly half of it. Weha's larger T800/400 lifter follows the same pattern, with 800 kg horizontal and 400 kg vertical capacity. The lower vertical rating is the one to remember when you plan to tip a piece on edge or carry it upright. These are maximum ratings under proper conditions, and the instruction manual lists the factors that reduce what any given lift can safely carry.

Setting Up the Air Supply

Run the lifter from a clean, dry air line capable of delivering at least the published 60 PSI at 2 CFM while other tools on the same circuit are working. A pressure drop elsewhere in the shop should never starve the lifter during a move. Keep the supply hose routed so it cannot snag on the stone, the hoist or passing carts, and make sure the hose length allows the full travel of the crane or jib without pulling tight. The built-in multi-filter and water trap help, but they work best when the shop air is already reasonably clean and dry.

Attaching to the Stone

Before every lift, wipe the area of stone where the pad will land and check the pad seal for debris, cuts or wear. Slurry, grit or a small chip under the seal is all it takes to create a leak. Center the pad over the piece as well as you can so the load hangs evenly, then engage the vacuum and watch the pressure gauge until it reaches the level the manufacturer specifies. Only then should you take up the slack on the hoist and raise the stone a short distance to confirm it is holding before making the full move.

Moving and Setting Down

Move steadily, keep the load low, and keep people out of the path and away from the area under the stone. Avoid swinging or jerking the hoist, which adds dynamic forces the rating does not account for. Set the piece down fully supported on the bench, cart or A-frame before releasing the vacuum, and keep a hand on the stone until it is stable. Long, thin pieces deserve extra attention: overhang beyond the pad puts bending stress on the stone itself, so a narrow strip can crack even when the lifter is holding perfectly.

Spotlight: The Weha T300 UNI-PAD combines a long 21.3 x 6 inch suction plate with an air-only venturi system that runs from a small compressor at 60 PSI and 2 CFM. For shops that already have compressed air at the bench and an overhead hoist, it offers a compact way to handle countertop sections, strips and sills up to its published 661 lb horizontal rating, with a safety vacuum tank and visible gauge built in.

Advanced Handling Tips for Fabricators and Installers

Know the rules that apply to your lifting. The ASME B30.20 standard for below-the-hook lifting devices includes a dedicated chapter on vacuum lifting devices, and some state programs adopt it directly; Washington's construction rules, for example, require vacuum lifting devices to be built to ASME B30.20. Those rules call for the rated load to be marked on the lifter, for a qualified person to inspect new, altered or repaired units, and for operators to check the pad seal and load surface for debris before and during every lift. Treat those checks as part of the job.

Respect the factors that reduce capacity. The Washington rules list several conditions that the instruction manual must address because they lower the rating of a lifter: the rigidity and strength of the load, overhang, surface condition, load angle, temperature, the number of pads and the vacuum level. Porous, textured or heavily honed surfaces can make a seal harder to achieve than a polished face does. Thin or fragile pieces may crack under their own weight when they overhang the pad. Plan every lift with these in mind instead of relying on the headline number.

Match the lifter to the work mix. A single-pad lifter in this class excels at the pieces a fabricator moves dozens of times a day, but full slabs and large tops call for heavier multi-pad equipment, clamps or forklift attachments with their own ratings. Many shops end up with a small family of handling tools so that each piece is moved by the device best suited to it. The T300 fills a specific gap between hand-carried pieces and slab-scale lifting rather than replacing everything else on the floor.

Build handling into the cutting plan. When sections leave the saw in sizes and orientations that the lifter can grab flat and centered, moves are quicker and safer. Leave enough clear surface on each part for the full pad to land, keep sink cutouts and narrow returns in mind when picking a grip point, and avoid placing the pad across a seam or an unsupported cutout. Small adjustments in nesting and staging can remove awkward lifts entirely, which protects both the stone and the people moving it.

On jobs that involve glass or metal panels alongside stone, as some commercial and architectural work does, check that the surface is flat and nonporous enough for a reliable seal and that the panel can carry its own weight without deflecting. Tenax lists glass and metal among the suitable materials for the T300, but each material still needs the same pre-lift checks. Clean the pad between materials so residue from one surface does not compromise the seal on the next, and confirm the gauge reading every time.

Train every operator, not just the regular one. A lifter that only one person knows how to use becomes a bottleneck, and a lifter used by someone who has never read the manual becomes a risk. Walk new team members through the air connection, gauge reading, pad inspection and the response if vacuum drops. Practicing the set-down procedure on scrap pieces builds confidence, and posting a short checklist near the hoist keeps the routine consistent across shifts and crews.

Caring for the Pad, Seals and Air System

The suction pad is a wear part, and its condition directly affects safety. Industry inspection guidance for vacuum lifters calls for checking pads for contamination, excessive wear, seal integrity and reduced friction. Tenax notes that the UNI-PAD rubber seals are quick to replace, which makes it practical to swap them at the first sign of cuts, tears, hardening or permanent deformation rather than running them until they leak. Keep a spare seal on hand so a worn one never tempts anyone to keep lifting with it.

Keep the pad clean. Stone slurry, polishing residue and grit settle on the rubber, and dried slurry can stop the seal from conforming to the surface. Wipe the pad after work sessions and before lifting a freshly polished piece, and store the lifter so the pad does not rest on a dirty floor or a sharp edge. A pad that is stored hanging or on a clean stand stays flatter and seals more reliably than one left lying face down on concrete.

Look after the air side as well. The multi-filter and water trap on the T300 exist to keep dust and moisture out of the pneumatic components, so empty the trap and service the filter on a regular schedule, more often in a wet shop. Inspect the supply hose and fittings for cracks, kinks and leaks. A compressed-air leak will not drop the stone by itself, but it wastes capacity and can mask a problem with the vacuum circuit, so fix it promptly rather than tolerating a constant hiss.

Test the vacuum system periodically. The ASME-based guidance describes an operational test in which a clean, smooth, nonporous surface is attached to the pad, the vacuum source is shut off, and the vacuum level must not fall faster than the manufacturer's specified rate. Warning devices and gauges are checked the same way. Running this test on schedule, and whenever the lifter has been repaired or has had a rough day, catches slow leaks before they turn into a problem during a real lift.

Keep records. Scheduled inspections under these rules are documented, and the inspection frequency increases with service severity, from yearly for normal service to more often for heavy or severe service. A simple log near the hoist, noting pad changes, filter service, gauge checks and test results, makes it easy to show that the lifter has been maintained, and it helps you spot patterns, such as seals that wear faster on one type of material. Note that Tenax lists a six-month manufacturer warranty on the T300.

Finally, take a lifter out of service the moment something seems wrong. A gauge that will not reach the expected level, a vacuum that bleeds down during a hold, a damaged pad or a cracked hose are all reasons to stop and fix the problem before the next move. The inspection guidance is clear that leaks beyond the manufacturer's specification, or an inability to reach the minimum vacuum level, take the lifter out of service. No deadline is worth a dropped top or an injured crew member.

To see current pricing and documentation, visit the Weha T300 UNI-PAD product page. If your work leans toward heavier pieces, compare it with the Weha T600 UNI-PAD pneumatic vacuum lifter, and browse the full vacuum lifter collection for multi-pad and electric options. For hand-held moves and seam work, our suction cup collection covers the smaller jobs, and the complete Weha range is gathered in one place.

Free Tool

Free Guides & Tools — Browse the free stone fabrication guides and calculators from Dynamic Stone Tools, from slab handling and lifting to cutting, polishing and installation planning around a vacuum lifter like the T300.

Explore Free Tools →

Lift Smarter, Not Harder

Find vacuum lifters, suction cups and handling gear sized for the pieces your shop moves every day.

Shop Vacuum Lifters →
Anterior Siguiente

Escribir un comentario

Tenga en cuenta que los comentarios se tienen que aprobar antes de que se publiquen.