Marble, terrazzo, and agglomerated-marble floors and counters lose their mirror gloss long before the stone itself wears out. A few seasons of foot traffic, cleaning chemicals, and routine wear dull the surface sheen even when the polish job underneath is otherwise sound, and a full re-honing and re-polishing visit is not always justified for that kind of dulling. For exactly that gap between full fabrication-shop polishing and a quick refresh, fabricators and restoration crews reach for a chemical polishing compound rather than running the whole resin-pad sequence again.
Tenax Marble Polishing Powder is the product Dynamic Stone Tools stocks for that job, and this spotlight sticks to what Tenax's own safety data sheet and catalog literature confirm about it rather than to assumptions about what a "marble polishing powder" probably contains. The product — Tenax Marble Polishing Powder — is made by Tenax Spa of Volargne, Italy, and distributed in the United States by Tenax USA. The sections below cover exactly what Tenax's documentation says the powder is, what it is for, how the catalog describes using it, and the safety handling the SDS specifies — nothing added, and travertine or limestone intentionally left out because Tenax's own documents do not name them for this product.

What Tenax Marble Polishing Powder Actually Is
Tenax's own safety data sheet identifies the product by its Italian name, Polvere lucidante marmo, with CAS number 6100-20-5 and EC number 204-874-6. Section 3 of that sheet lists the composition as 100 percent potassium hydrogen oxalate, the potassium salt of oxalic acid rather than free oxalic acid itself. That distinction matters for anyone assuming every marble-polishing powder on the market is the same chemistry: Tenax's own paperwork names a specific oxalate salt for this exact product, not a generic "oxalic acid compound" label.
Section 9 of the SDS describes the physical form as a white, odourless solid powder that is soluble in water. Section 12.2, further down the same document, puts a number behind that description: a water solubility above 10,000 mg per liter for the potassium hydrogen oxalate itself. No pH figure, melting point, or shelf-life figure is given anywhere in the document, so none of those numbers appear in this article — where Tenax's own paperwork is silent, the honest answer is that the number is not published, not a guess at what it might be.
Chemical polishing powders are one of several ways a shop restores gloss on calcite-based stone; resin-bond polishing pads and floor-crystallization systems are two others, and each follows a different process with different equipment. Dynamic Stone Tools carries dedicated articles on resin polishing powders and on crystallization floor treatments for those two paths; this article only covers the Tenax oxalate powder and does not restate what those pieces already explain.
Section 1.2 of the SDS states the product's intended use plainly: "Polishing powder for marble." Section 2 classifies the mixture as hazardous under the OSHA Hazard Communication Standard (29 CFR 1910.1200), carrying Acute Toxicity Category 4 for both ingestion and skin contact, with hazard statements H302 ("harmful if swallowed") and H312 ("harmful in contact with skin") and the signal word "Warning." That classification is the reason the handling guidance later in this article is not optional shop etiquette — it follows directly from how Tenax itself classifies the powder.
Deciding whether a dulled marble surface needs this kind of powder touch-up or a full mechanical re-polish is mostly a matter of looking at what caused the dulling. A haze from repeated light scuffing, hard-water film, or general foot traffic sits in the same category the catalog sheet addresses with "general maintenance" language; a surface with actual pitting, deep scratches, or an etch mark gouged below the polished plane is a mechanical problem that a buffed-on powder cannot fill in. Fabricators who keep both options in mind avoid two common mistakes: running a full resin-pad sequence on a surface that only needed a buffed touch-up, and expecting a polishing powder to fix damage that is actually below the surface.
Working the Powder Into a Shop Routine
What the Catalog Sheet Confirms
A Tenax USA catalog sheet titled "Polishing Powders" names the same part numbers Dynamic Stone Tools sells under: POLVERMA1KG for the 2 lb (1 kg) container and POLVERMA for a 33 lb (15 kg) bucket. The same sheet states, in Tenax's own words, that "Tenax polishing powders are formulated specifically to create a high gloss finish on stone" and that the marble powder "is designed for Marble, Terrazzo, and agglomerated marble surfaces." It also states the powder "may be used on countertops, floors, and as a general maintenance product." Those three surfaces — marble, terrazzo, and agglomerated (engineered) marble — are the only ones Tenax's own literature names for this product.
Where It Sits in the Finishing Sequence
On application, the catalog sheet states only that the powder is "simple and easy to use," without a separate method, tool, or equipment-speed instruction beyond that. In shop practice, a buffing powder like this is worked into the stone with a buffing pad or wheel rather than a cutting or grinding accessory — the felt buffing wheel Dynamic Stone Tools stocks for use with polishing powders is that kind of accessory. The powder is a finishing step, not a flattening or scratch-removal step; a surface that is chipped, deeply scratched, or out of flat still needs the mechanical pad sequence first, and the polishing powder is what brings the final sheen back up afterward.
Marble Powder vs. Granite Powder
The same Tenax USA catalog sheet sells a second, separate powder for a different stone family. The table below keeps the two straight, using only the part numbers, sizes, and target surfaces the catalog sheet itself states.
| Product | Target surfaces (per catalog) | Sizes / part numbers |
|---|---|---|
| Tenax Marble Polishing Powder | Marble, terrazzo, agglomerated (engineered) marble | 2 lb / 1 kg (POLVERMA1KG); 33 lb / 15 kg (POLVERMA) |
| Tenax Granite Polishing Powder | Granite, all types | 2 lb / 1 kg (POLVERGR1KG); 33 lb / 15 kg (POLVERGR) |
Reaching for the wrong one of the two is an easy mistake on a mixed job, and the catalog sheet gives no indication the two powders are interchangeable across stone families. Keep the marble version with the marble tooling cart and the granite version with the granite cart, and label the 33 lb buckets clearly if a shop runs both sizes side by side.
Spotlight: Tenax Marble Polishing Powder is a 100 percent potassium-hydrogen-oxalate compound that Tenax Spa makes specifically for marble, terrazzo, and agglomerated marble, described on its own catalog sheet as simple and easy to use for bringing up a high-gloss finish on countertops, floors, and general maintenance work.
Handling the Powder Safely in the Shop
Section 6 of the SDS gives specific guidance for a spill: if there is no contraindication, spray the loose powder with water to keep it from becoming airborne dust, and avoid breathing any resulting vapors, mists, or gases. The same section states the product must not be allowed to enter the sewer system or come into contact with surface water or groundwater, so a shop's slurry and wastewater handling needs to treat spilled powder the same way it treats other process chemicals rather than sweeping it toward a floor drain.
Section 5.2 of the SDS flags a hazard that is easy to overlook for a powder marketed as a finishing compound: it is combustible, and when released into the air in sufficient concentration near an ignition source it can form an explosive dust-air mixture. The sheet also notes that combustion of the potassium hydrogen oxalate can generate caustic potassium oxide fumes. None of that makes the product unusually dangerous for normal buffing use, but it is a reason to keep dry powder away from open flame or spark sources during mixing and to clean up spilled powder rather than letting it accumulate in a dusty corner.
Section 8 of the SDS lists the personal protective equipment Tenax specifies: penetration-resistant work gloves meeting OSHA 29 CFR 1910.138, airtight protective goggles meeting OSHA 29 CFR 1910.133, and a NIOSH-certified filtering facemask meeting NIOSH 42 CFR 84 and OSHA 29 CFR 1910.134, selected according to a workplace risk assessment. The same section also calls for category I professional long-sleeved overalls and safety footwear. For general dust exposure, the SDS references the ACGIH occupational exposure levels for particulate not otherwise classified — 3 mg/m3 for the respirable fraction and 10 mg/m3 for the inhalable fraction — as the benchmark a risk assessment should use.
Section 4 of the SDS lays out first aid in plain terms: for eye contact, remove contact lenses if present and rinse with plenty of water for at least 15 minutes with the eyelids held open, then seek medical advice if irritation persists; for skin contact, remove contaminated clothing and wash immediately with plenty of water, and wash the clothing before wearing it again; for inhalation, move to open air and get medical attention if breathing becomes difficult. Posting that sheet, or at least this summary of it, near wherever the powder is mixed costs nothing and answers the question faster than searching for the SDS after the fact.
Maintenance and Long-Term Use Considerations
Section 7.2 of the SDS is specific about storage: keep the product only in its original container, sealed, in a well-ventilated place, away from direct sunlight. Beyond that, the SDS does not publish a shelf-life figure, so a shop rotating stock should treat an opened container the way it treats any other powdered chemical — reseal it promptly after use and keep it dry, since moisture pickup in a powder changes how evenly it mixes long before any printed expiration date would apply.
On the broader toxicology question that fabricators reasonably ask about any shop chemical, Section 11 of the SDS states the product is not considered a carcinogen by IARC, ACGIH, NTP, or OSHA. Section 15 adds that under California's Proposition 65 the product does not contain any substance known to the state to cause cancer, reproductive harm, or birth defects. Neither statement changes the Acute Toxicity Category 4 classification already noted above, and the PPE called for in Section 8 still applies on every job, not just the first one.
The catalog sheet's note that the powder doubles as "a general maintenance product" is worth reading literally: it supports a lighter, more frequent touch-up pass between full fabrication-shop repolishing visits, rather than being limited to one-time restoration work. A felt or buffing wheel that has loaded up with old polishing compound from a previous job should be cleaned or swapped before it is used again, since carried-over grit from an unrelated job can scratch a surface the fresh powder is supposed to be finishing.
Because Tenax's own documentation names only marble, terrazzo, and agglomerated marble for this specific powder, do not extend it to travertine, limestone, or any other calcite-based stone on the assumption that "it is all basically marble." A separate Tenax powder exists for granite, which underlines that Tenax treats stone families as distinct markets rather than selling one powder as a universal fix. When a job involves a stone this product's documentation does not name, test in an inconspicuous area first, and when in doubt, choose a product whose own paperwork names that stone.
How often that touch-up pass is worth running depends on the traffic the surface sees. A commercial lobby floor in marble or terrazzo sees far more foot traffic, grit tracked in from outside, and cleaning-chemical exposure in a month than a residential kitchen counter sees in a year, so a maintenance program built around this kind of powder makes more sense on a schedule tied to visible dulling than to a fixed calendar date. Keeping a simple log of when a floor or counter was last buffed, and what it looked like beforehand, gives a crew a faster answer than re-inspecting the whole job from scratch every time a customer calls about a dull patch.
Disposal guidance in Section 13 of the SDS is equally specific: reuse the product when possible, treat neat residues as special non-hazardous waste, and dispose of them through an authorized waste management firm in compliance with national and local regulations. Contaminated packaging falls under the same instruction. None of that is unusual for a shop that already manages slurry and spent chemical containers correctly, but it is worth folding into the same disposal routine rather than treating a polishing-powder tub as ordinary trash.
For readers comparing this specific product against other finishing chemistries before choosing one, Dynamic Stone Tools' guide to oxalic acid polishing compounds covers the broader category of free-oxalic-acid products and their limits, which is a different chemistry than the potassium-oxalate salt named in this product's own SDS; the crystallization-treatment article linked earlier covers a catalyst-based floor process that is a different method entirely, applied with different equipment and a different safety profile. Reading this spotlight alongside those two keeps the distinctions straight rather than treating every "marble polishing" product as one interchangeable category.
Free Tool
Free Guides & Tools — the hub for Dynamic Stone Tools' interactive selectors, including Stone ID, the diamond blade guide, the polishing pad sequence builder, the adhesive and sealer guide, and the job kit builder, each built on the live catalog and manufacturer-verified specs.
Open the Free Guides →Keep Marble and Terrazzo Gloss Shop-Ready
Stock the polishing powders, buffing wheels, and stone-care chemistry your crew actually reaches for between jobs.
Shop Stone Sealers & Care →