Envío el mismo día antes de las 12 PM ET | Llame al 703-957-4544

Echa un vistazo a nuestras marcas. MAXAW, KRATOS, RAX y más. Más información

Stonify, our Official Tech Partner for Fabricators. Book a free demo

Cyclone Convex Disk: A Curved Surface Polishing Spotlight

Cyclone Convex Disk: A Curved Surface Polishing Spotlight

Dynamic Stone Tools

A countertop edge rarely stays flat all the way around. Ogee profiles roll from a concave hollow into a convex bead, bullnose corners curve continuously, and an undermount sink cutout leaves an inside radius that a flat-faced pad cannot reach without rocking off the stone. Dynamic Stone Tools stocks the Diamax Cyclone Convex Disk for exactly that geometry: a domed polishing disk that keeps its face in contact with a curved or concave surface instead of skipping across the high points the way a flat pad does. It sits inside the wider Diamax Cyclone wet polishing line and is sold as a full grit progression plus two buffing stages, so a shop can run one curved profile from coarse grinding through to a finished gloss with a single family of disks.

This spotlight covers what the Cyclone Convex Disk actually is according to Diamax's own product page, how it is set up on a machine and run wet, the full grit-to-grit sequence Diamax publishes for it, and where it earns its place on an ogee edge or inside a sink cutout corner that a standard flat pad or a drum wheel cannot finish cleanly. It also covers pad care, when to retire a worn disk, and how this disk relates to the flat Cyclone pads and drum wheels a shop likely already owns, since none of these tools replace each other - they cover different parts of the same curved or recessed surface.

Diamax Cyclone Convex Disk

What the Cyclone Convex Disk Is Built to Do

Diamax's own listing for the product describes the Cyclone Convex Disk in plain, narrow terms: the pads are useful for ogee edge polishing, and they are good for polishing difficult-to-reach areas like the inside corners of sink cutouts. That is a deliberately narrow job description, and it matters - this is not a general-purpose flat polishing pad pressed into service on a curve. The dome of the disk is shaped so its working face can follow a concave radius or an inside corner without the outer edge or the center lifting off the stone, which is exactly the contact problem a flat pad runs into on anything but a straight or gently convex surface.

Diamax rates the disk for granite and engineered stone, both worked with diamond abrasive because of their hardness and, in the case of engineered quartz surfacing, a resin-bound mix of crushed quartz that still needs a diamond-rated tool to cut or grind cleanly. The disk carries diamond abrasive bonded to a resin matrix across seven grit stages plus two non-grit buffing stages, so the working sequence moves from aggressive stock removal at the coarse end down to a mirror finish - the same logic as a flat polishing pad set, just carried on a dome instead of a flat face.

The disk attaches with a hook-and-loop (velcro) back and is sized for a 3-inch backer pad, matching it to the same small air polishers and angle grinders fabricators already use for edge detail work rather than a full-size wet polisher head. Diamax lists the tool as compatible with an angle grinder or an air polisher, which keeps the disk usable both on a stationary bench setup and handheld on a slab already set on the line - a practical point for sink cutout work, where the piece is frequently already templated and cut before the inside corners get their polish pass.

Every grit and buff stage in the line carries the same maximum operating speed - 2,500 RPM - according to Diamax's specification table for the product. A single speed ceiling across the whole set is a convenience for a shop running the full sequence on one tool: there is no need to slow the machine down or speed it up between the coarse 50-grit stage and the 3,000-grit finishing stage, only to control feed pressure and dwell time as the surface gets smoother. Running any stage of this disk faster than the rated 2,500 RPM is outside Diamax's own specification for the tool.

Setting Up and Running the Convex Disk

Backer Pad, Water, and Machine Setup

Because Diamax specifies the Cyclone Convex Disk for wet use only, the first setup decision is water delivery, not grit choice. A dome-shaped disk concentrates contact at the crown of the curve rather than across a flat face, so the same water volume that cools a flat pad evenly can run off a convex surface faster than it reaches the contact point. Fabricators running this disk on an angle grinder typically feed water from a side-mounted line or a drip bottle aimed just ahead of the disk's contact point on the stone, rather than relying on a wet polisher's built-in flood, which is sized for a flat pad's footprint.

Mount the disk on a 3-inch backer pad that matches the hook-and-loop back Diamax specifies, and check the backer pad's own arbor against the angle grinder or air polisher before starting - a backer pad sized for a different pad family will not seat the convex disk flat against its own hub, which throws off the dome's contact geometry before the first pass is made. Dynamic Stone Tools stocks the Alpha Professional Tools Turboshine Dual Adapter 3 Inch Backer Pad alongside the Cyclone Convex Disk itself, so the two are typically ordered together rather than sourced separately.

The Grit Sequence

Diamax publishes the Cyclone Convex Disk as nine SKUs, one per grit stage plus the two buffing stages, all rated to the same 2,500 RPM ceiling. The table below reproduces that specification exactly as Diamax lists it, so a shop ordering the sequence knows which item number covers which stage before it reaches the bench.

Stage Diamax Item # Max RPM
50 Grit PDCX30050 2,500
100 Grit PDCX30100 2,500
200 Grit PDCX30200 2,500
400 Grit PDCX30400 2,500
800 Grit PDCX30800 2,500
1,500 Grit PDCX31500 2,500
3,000 Grit PDCX33000 2,500
Black Buff PDCX3BB 2,500
White Buff PDCX3BW 2,500

Working Curves, Ogee Profiles, and Sink Cutout Corners

On an ogee edge, the profile rolls through a concave section and a convex section joined by a short flat transition, and each of those three sections wants a slightly different pad shape to stay in full contact. The convex disk is the tool for the concave hollow and the inside transition, where a flat pad would only touch at the two high points and burnish a pair of bright lines instead of an even satin or gloss finish across the curve. Fabricators typically finish the flat sections of an ogee with a standard flat Cyclone pad and switch to the convex disk only for the hollow, rather than trying to run one pad shape across the whole profile.

Inside a sink cutout, the same contact problem shows up at the corners: a flat pad or even a standard Diamax Cyclone Polishing Drum Wheels for Granite can true up the straight runs of the cutout, but the inside radius where two cuts meet is exactly the difficult-to-reach spot Diamax's own product description calls out for this disk. Working that corner means slowing the feed rate and letting the dome ride the radius rather than pushing straight through it, since forcing the disk the way it would move across a flat run will skate it off the tight curve and leave an under-polished arc at the corner itself.

Run the full grit progression in order - 50, 100, 200, 400, 800, 1,500, then 3,000 - without skipping stages on a curved surface, because each stage on a dome has less working contact area than the equivalent flat pad and relies on the full sequence to remove the scratch pattern left by the one before it. Finish with the black buff stage for a honed look or the white buff stage for a higher gloss, since Diamax lists both as terminal stages after 3,000 grit rather than as an alternative to it.

Spotlight: The Diamax Cyclone Convex Disk is a narrow-purpose tool - Diamax's own listing limits it to ogee edge polishing and the inside corners of sink cutouts on granite and engineered stone, wet only, at a maximum of 2,500 RPM across every grit and buff stage in the nine-piece set.

Advanced and Trade-Specific Technique

Shops that run a lot of ogee and bullnose edge work usually keep the convex disk paired with the flat Cyclone pads rather than trying to make either one cover the whole profile. The practical hand-off point is the transition line where the curve flattens out - working past that line with the convex disk tends to round over what should stay a sharp transition, while stopping the flat pad short of the hollow leaves the under-polished arc described above. Marking that transition line on a sample piece before a production run helps a new operator learn where to switch tools without guessing on a customer's slab.

Both of the materials Diamax rates this disk for - granite and engineered stone - contain crystalline silica, and any dry grinding or dry buffing step on them generates respirable dust regulated under OSHA's crystalline silica standard, which sets a permissible exposure limit of 50 micrograms per cubic meter as an 8-hour time-weighted average, with an action level of 25 micrograms per cubic meter. Running this disk wet, as Diamax specifies, keeps dust down at the source during the polishing stage itself; a shop still needs its own dry-cutting and dry-grinding steps elsewhere in the same job controlled to the same standard, since wet polishing on one tool does not cover a dry process on another.

Pressure control matters more on a dome than on a flat pad, because the contact patch is smaller and heats up faster if an operator pushes the way they would on a flat run. Light, even pressure with steady motion across the curve - rather than dwelling in one spot to chase a stubborn scratch - keeps the diamond working across the full grit stage instead of burning a hot spot that can show up as a dull patch once the piece reaches the buffing stages. If a dull patch does appear, dropping back one grit stage over the whole curve, not just the spot, keeps the finish even.

Inspect the finish on a curved section under raking light rather than straight overhead light, since raking light shows contact gaps and flat spots on a dome far more clearly than it shows on a flat polished face. A shop that signs off curved ogee or sink-corner work under the same lighting it uses for flat tops risks missing exactly the uneven-gloss defect this disk is built to prevent, so a second look under a raking angle before the piece ships catches most of these misses.

Maintenance and Pad Life

Rinse the disk and its backer pad after each use, since dried slurry left in the hook-and-loop backing reduces how firmly the disk seats on the next job and can throw the dome slightly off-center against the pad. A disk that is not seated flat on its backer pad will contact the stone unevenly even before grit wear becomes a factor, so a clean, dry backing is as much a finish-quality issue as a durability one.

Watch the working face for the same wear signs that show up on any resin-bond diamond pad: a glazed, shiny surface that no longer cuts at the rate it did new, or visible thinning of the resin at the crown of the dome where contact concentrates. Because the convex shape puts most of the wear at that crown rather than spread evenly across the face the way a flat pad wears, a disk can look serviceable at the edges while the working point is already worn past the diamond layer - check the crown specifically, not just the overall pad.

Keep a full grit set together as a unit rather than restocking single stages piecemeal, since a shop that runs out of the 400 or 800-grit stage mid-sequence ends up either skipping a stage on a curved surface - which leaves scratch pattern from two grits back - or stopping a job to reorder. Because the disk only comes in this one 3-inch size per Diamax's listing, there is no larger or smaller version to substitute if a stage runs short; the fix is keeping the full nine-piece sequence stocked, not swapping in a different-sized disk from another line.

Store the disks away from direct heat and out of standing water between jobs, and keep each grit stage's disks together and labeled, since the grit number is marked on the disk itself but gets harder to read once a disk has seen use. A shop running several curved-edge jobs a week benefits from a dedicated small bin for this one tool family rather than mixing it into a general pad drawer with flat Cyclone pads and drum wheels, both of which look similar at a glance but are not interchangeable with the convex disk's domed face.

The Cyclone Convex Disk is one piece of a larger sink-cutout and curved-edge toolkit, and it is worth reading about alongside the tools that handle the rest of that same job rather than in place of them. Polishing Undermount Sink Cutout Edges: Drum Wheels, Pads and Sequence covers the straight runs of a cutout with drum wheels and flat pads before a convex disk like this one takes the inside corners. Diamax Cyclone SuperFlex Pads: Complete Finishing Guide covers the flat pads in the same Cyclone family that this disk is meant to hand off to on straight and gently convex sections. For the grinding stage before any of these polishing tools, Cup Wheel Guide: Turbo, Flat, Pineapple & Drum Wheels covers the cup wheels that rough out a cutout or edge before a finishing sequence like this one begins. The wider Polishing Pads collection carries the flat-pad side of that same work.

Free Tool

Polishing Pad Sequence Builder — pick your stone, wet or dry method, and target finish to get the exact grit sequence, from #50 to #3000, for granite, marble, quartzite or engineered stone.

Build My Pad Sequence →

Finish Every Curve the Same Way, Every Time

Stock the full Diamax Cyclone Convex Disk grit set alongside the backer pads and drum wheels that round out a sink-cutout and curved-edge job.

Shop Polishing Pads →
Anterior Siguiente

Escribir un comentario

Tenga en cuenta que los comentarios se tienen que aprobar antes de que se publiquen.