Envío el mismo día antes de las 12 PM ET | Llame al 703-957-4544

Echa un vistazo a nuestras marcas. MAXAW, KRATOS, RAX y más. Más información

Stonify, our Official Tech Partner for Fabricators. Book a free demo

Akemi Acid Protect UV Lamp: A UV Curing System Spotlight

Akemi Acid Protect UV Lamp: A UV Curing System Spotlight

Dynamic Stone Tools

Marble and limestone counters etch the moment a splash of vinegar, wine, or citrus juice sits on the surface a little too long, and no amount of topical sealer stops that reaction once the stone is exposed bare. Akemi built a different answer: a radiation-curing lacquer called Acid Protect that stays liquid and workable on the slab until a fabricator deliberately hardens it with ultraviolet light, at which point it becomes a protective film the household acids cannot reach. The hardware that makes that cure happen on the bench or on a finished countertop is the Handheld UV-Lamp 500 AP, sold with its bulb and transformer, and it is the subject of this spotlight.

A UV-curing coating is only as good as the lamp that cures it, so this article stays close to what Akemi itself publishes about the lamp and the two Acid Protect products it serves: how the chemistry cures on demand, what the lamp's own specification sheet states about wavelength and power draw, how a shop runs the cure cycle, what ultraviolet exposure does to unprotected eyes and skin, and how to keep a curing lamp in service for the long run. Every number below traces back to Akemi's own product pages or to a federal safety source, and nothing here is a store description dressed up as a fact.

Akemi Acid Protect UV Lamp with Bulb and Transformer - UV Curing System

How Akemi's UV-Curing Acid Protect System Works

Acid Protect Brush and Acid Protect Spray are both described by Akemi as liquid, radiation-curing UV protective lacquers with a smooth, self-levelling flow. The working principle is the same for both: the lacquer does not set on its own schedule the way a two-part epoxy does. It remains workable on the surface until it is deliberately exposed to ultraviolet light from a lamp Akemi approves for the purpose, and only then does it harden into a protective film. That separation between "applied" and "cured" is what lets a fabricator take as long as the job needs to lay the coating down evenly before committing to a hard finish.

The two products are built for different points in the workflow. Acid Protect Brush is meant for a brush, toothed spatula, roller, or spray application directly on new or already-installed and laid surfaces, which makes it the one a fabricator reaches for on a repair or a touch-up after a counter is already in the kitchen. Acid Protect Spray, by contrast, is a highly liquid version Akemi describes as applied by spraying with a professional gun inside a paint cabin, for a lint-free finish on surfaces before they are installed, and Akemi specifies it for indoor use only. Both cure under the same family of AKEMI-approved UV lamps, including the Handheld UV-Lamp 500 AP this article covers.

What the cured film actually stops matters as much as how it cures. Akemi states that both Acid Protect products protect marble, limestone, and other acid-sensitive stone against mechanical damage and against common household stain formers — vinegar, citric acid, red wine, coffee, cola, and cooking oil — as well as against acidic cleaners such as sanitary cleaners. That list reads like a kitchen countertop's worst-case scenario on purpose: Akemi positions the coating specifically for worktops, dining tables, and washbasins made from calcareous stone, the exact material class that etches on contact with anything acidic.

Akemi also publishes performance figures for the cured film on Acid Protect Brush: temperature resistance up to 302°F (150°C), high scratch resistance with the ability to polish out minor scratches after the fact, and a composition that includes 8% carbon sourced from renewable raw materials. Akemi further states that, once hardened, Acid Protect Brush is harmless to health upon contact with food products, a claim the company says is certified by an external German testing institute. Gloss on both products is adjustable after curing, from a matte finish to a high-gloss finish, by controlling how the coating is exposed to the lamp.

Running the Handheld UV-Lamp 500 AP: Specs, Setup, and the Cure Cycle

Lamp Specifications

Akemi's own product page for the Handheld UV-Lamp 500 AP lists a compact set of figures, and this table repeats only what that page states rather than anything inferred from the listing. The lamp's model number on Akemi's side is 62082, and the separate replacement bulb carries Akemi's item number 62083.

Property Detail (Akemi spec)
Main wavelength 365 nm (UV-A)
Power consumption 500 W
Surface light output 100 mW/cm²
Dimensions (L x W x H) 214 x 120 x 155 mm
Cooling Air-cooled
Cures Acid Protect Brush and Acid Protect Spray
Replacement bulb Item 62083 (sold separately)

The Cure Cycle on the Bench

Because Akemi ties gloss control to UV exposure rather than to the coating's own chemistry, the practical sequence on a job is to lay down Acid Protect Brush or Acid Protect Spray evenly first, then pass the Handheld UV-Lamp 500 AP over the coated area to bring it to the finish level the job calls for, from matte through high gloss. Akemi does not publish a fixed cure time for the 500 AP on its product page, and this article will not invent one; the honest statement is that the coating hardens on demand once it meets UV-A light from an approved lamp, and the fabricator controls the result by how the lamp is used rather than by a stopwatch figure Akemi has not released.

Akemi is explicit that only UV lamps it approves should be used to cure Acid Protect, and the Handheld UV-Lamp 500 AP is one of those approved units, built and sold specifically for this coating family rather than as a general-purpose UV light repurposed for stone work. Both the lamp and the two coatings are marked for professional use only on Akemi's own pages, which is consistent with how the system is positioned: a shop tool paired with a shop-grade chemical, not a consumer kit.

The 500 W draw and air-cooled housing mean the lamp behaves like other corded electric shop tools rather than a battery-powered light — plan for a dedicated outlet circuit on a busy bench, and route the cord away from the slab edge before starting the pass. The 214 x 120 x 155 mm body is small enough to work a sink cutout or an under-mount edge by hand, which matters for the touch-up and repair work Acid Protect Brush is built for. Dynamic Stone Tools stocks the replacement bulb for the UV curing system as its own line item, which is worth keeping on the shelf next to the lamp rather than ordering only after a bulb fails mid-job.

Spotlight: The Akemi Acid Protect UV Lamp with Bulb and Transformer is the complete curing unit for Akemi's Acid Protect Brush and Acid Protect Spray coatings — a 365 nm UV-A handheld lamp, air-cooled, supplied ready to run with its bulb and transformer, built to harden the coating on demand and let the operator dial the finish from matte to high gloss.

Trade Practice: UV Exposure Safety and Handling on the Bench

A 365 nm lamp sits squarely in the UV-A band, and UV-A is not the harmless end of the ultraviolet spectrum some shops treat it as. OSHA's Technical Manual, in the chapter covering non-ionizing radiation health hazards, lists photochemical UV cataract as an eye effect associated with UV-A exposure, alongside skin burn as an effect that spans the UV-A, visible, and infrared ranges. The same chapter notes that exposure in the UV-B range is the most injurious to skin and raises the possibility of radiation carcinogenesis from UV-B acting on DNA — context that explains why Akemi, and OSHA, both treat any UV curing lamp as equipment that needs real handling discipline, not a glorified flashlight.

OSHA's own recommendation for skin protection against UV exposure is to use skin covers and sunscreen creams, and for the hands specifically to use gloves — tightly woven fabrics and opaque gloves give the best protection. For the eyes, OSHA calls for eye-protection devices appropriate to the radiation source whenever engineering controls cannot eliminate the hazardous exposure on their own. Translated to the bench: keep bare skin out of the lamp's beam path, wear gloves while running a pass, and put on UV-rated eye protection before switching the lamp on, every time, not only when the pass runs long.

Akemi's own professional-use-only marking on both the lamp and the two coatings is a signal worth taking literally rather than as boilerplate. Acid Protect Spray's application method — a professional spray gun inside a paint cabin, indoor use only — exists specifically to keep overspray and UV exposure contained to a controlled booth rather than an open bay where other people are working nearby. Acid Protect Brush, applied with a brush, spatula, roller, or spray directly on an installed surface, does not have that booth to rely on, so the UV discipline has to travel with the lamp itself: clear the area of bystanders, and do not let the lit bulb point anywhere a coworker might walk through the beam.

Shops that run both Acid Protect products tend to split the work by where it happens rather than by who does it: Spray stays at the fab shop, on slabs still on the rack, cured under controlled booth conditions before the piece ever reaches a truck; Brush travels to the jobsite for the touch-up a shipping nick or an installer's slip exposes, cured in place with the handheld 500 AP. Keeping that split explicit in a shop's own procedure sheet avoids the common mistake of trying to spray-gun a coating indoors outside the cabin because the brush bottle ran dry.

Maintenance, Storage, and Long-Term Care of the Curing System

The single consumable on this tool is the bulb, and Akemi sells it under its own item number, 62083, as a part distinct from the complete 62082 lamp-and-transformer set. A shop that depends on Acid Protect for warranty-covered repairs or for pre-installation spraying should treat that bulb the way it treats a diamond blade's segments: order a spare before the current one is the only one on hand, not after a job stalls waiting on a part.

Because the lamp is a corded, air-cooled electrical unit rather than a sealed battery tool, the same storage habits that protect any shop power tool apply here: keep it off a wet bench, keep the cord away from standing water or coolant lines near a saw, and store it somewhere the bulb housing will not take an impact from a dropped slab offcut. None of that is an Akemi-published specification — it is ordinary shop practice for corded UV equipment, and this article is not attaching a number to it that Akemi has not stated.

Longer term, the coating itself is the part of the system that ages on the installed countertop, not the lamp. Akemi's own scratch-resistance and heat-resistance figures for Acid Protect Brush describe the cured film, and a fabricator revisiting a counter years later for a scratch or a chip should expect to recoat with the same Brush product rather than hunting for a different repair chemistry — Akemi built the self-levelling, touch-up-friendly version of the lacquer for exactly that return visit. Dynamic Stone Tools' broader Stone Sealers & Care collection is the place to look for the day-to-day cleaners that keep a cured Acid Protect surface presentable between repairs, since routine cleaning product choice sits outside what Akemi's Acid Protect documentation itself specifies.

A shop that stocks the lamp, the bulb, and both Acid Protect products together avoids the most common failure mode on this system, which is not a chemistry problem at all: it is reaching for an unapproved UV light because the approved one was not on the truck. Akemi's repeated point across its Brush, Spray, and lamp documentation is that curing depends on a lamp it has approved for the purpose, and the 500 AP exists precisely so a fabricator does not have to guess whether some other UV source on hand will do the job.

Acid etching on calcareous stone is a problem Dynamic Stone Tools covers from more than one angle, and this spotlight on the curing hardware is deliberately narrow by comparison. For the broader picture of keeping an etch-prone counter out of trouble in the first place, see how to protect stone from etching caused by spills, which focuses on day-to-day prevention rather than on a specific curing system. For what to do once etching has already happened on an unprotected surface, marble etching: causes, prevention, and DIY repair covers the causes and repair side in more general terms. This article, by contrast, stays on the one piece of equipment a shop needs to put Akemi's own acid-resistant coating to work in the first place.

Free Tool

Free Guides & Tools — the hub of Dynamic Stone Tools' free interactive selectors: Stone ID, the Diamond Blade Selector, the Polishing Pad Sequence Builder, the Adhesive & Sealer Guide, and the Countertop Job Kit Builder, each matched to your stone and project from live catalog and manufacturer-verified data.

Explore the Free Tools →

Keep acid-sensitive stone covered, cure to cure.

Shop the sealers, enhancers, and daily-care products that keep a protected marble or limestone surface looking right between repairs.

Shop Stone Sealers & Care →
Anterior Siguiente

Escribir un comentario

Tenga en cuenta que los comentarios se tienen que aprobar antes de que se publiquen.