Same-Day Shipping Before 12 PM ET | Call 703-957-4544

Check out our brands. MAXAW, KRATOS, RAX and more. Learn more

Stonify, our Official Tech Partner for Fabricators. Book a free demo

Oakley Stone: Working Idaho's Rocky Mountain Quartzite

Oakley Stone: Working Idaho's Rocky Mountain Quartzite

Dynamic Stone Tools

Oakley stone is the trade name most of the trade uses for a glittering, mica-rich building stone quarried in the mountains south of Oakley, in Cassia County, in southern Idaho. Dealers and geologists also call it Rocky Mountain quartzite or Idaho quartzite, and all three names describe the same metamorphic rock: a hard quartzite with thin, flattened mica layers running through it that let a quarry worker split a thick plate into several thinner sheets along its own natural grain, almost the way a book falls open along its spine. The stone ships as flagstone, ledge veneer and thin sawn veneer across the United States, Canada and parts of Europe, and it remains one of the few American building stones still extracted largely by hand.

For a fabricator who normally saws granite or engineered quartz slabs into countertops, Oakley stone is a different trade inside the same shop: most of the shaping happens by splitting and chiseling rather than by diamond blade, the material arrives in irregular plates instead of calibrated slabs, and the selling point is a natural cleaved face, not a polished one. This article covers the geology that makes the splitting possible, the product forms a shop actually buys and sells, how to cut, drill and set the stone without losing material to the mica planes, and what happens to it outdoors over the long run.

What Oakley Stone Actually Is

Geologists describe Oakley stone as a micaceous quartzite, and the Idaho press that has interviewed them over the years uses the same word. The original material was a quartz-rich sandstone that also carried thin layers of clay. As the surrounding rock was buried, heat and pressure recrystallized the quartz grains into an interlocking, low-porosity mass while the clay layers were squeezed and flattened into sheets of mica sandwiched between the harder quartzite beds. Geologists quoted in Idaho's Magic Valley press date the original sediment to roughly 620 million years ago, in the Neoproterozoic, with a later episode of faulting around 100 million years ago - the same mountain-building event that raised the Albion Mountains - lifting the rock close enough to the surface to quarry it today.

That mica is the whole reason the stone behaves the way it does. It is sold as quartzite, not as a schist or a slate, because the dominant mineral by volume is still quartz; the mica is a minority component concentrated along bedding-parallel partings. Those partings are what let a quarry worker drive a chisel or a hydraulic splitter along the plane and open a single thick plate into two, three or more thinner sheets, each one still structurally a quartzite rather than a flake of mica. The same partings are also why the finished stone shows a faint sheen on its cleaved face wherever light catches the mica flakes, which is part of what gives individual pieces their "silver," "gold" and "silver sheen" trade names at the quarry.

The quarries themselves sit on the west slope of Middle Mountain, in the Albion Mountains, a short drive south of the town of Oakley and not far from City of Rocks National Reserve. Commercial quarrying there dates to the late 1940s, and at various points roughly a dozen companies have worked pits on the mountain; today's active quarriers include Northern Stone Supply, Scrivanich and Sawtooth Stone, among smaller operators. The stone has supplied builders and homeowners well beyond Idaho - Frank Lloyd Wright specified it for Teater's Knoll, the studio he designed near Hagerman for the artist Archie Boyd Teater, which is still cited as the architect's only Idaho project built for a specific client and site.

A pallet of Oakley stone is sold by color grade more than by exact dimension, because splitting along a natural mica plane cannot be held to the tolerances of a diamond saw. Quarry catalogs group pieces into named lines - silver and silver-heritage tones, honey or sunset-gold tones, and a mica-bright "silver sheen" grade - and a shop ordering for a single wall or patio needs to specify the grade, not just "Oakley stone," or risk a pallet that mixes cooler and warmer pieces side by side.

Working It in the Shop and on the Job

Splitting Along the Grain

Most Oakley stone still leaves the quarry the way it has for decades: a worker finds the mica parting with a chisel or wedge set, then opens it with a hand sledge, a hydraulic splitter, or on bigger pieces a guillotine-style splitter that drives a blade along the plane under hydraulic pressure. Freshly quarried plates can run from roughly a quarter inch up to several inches thick and several feet across before they are broken down further into the flagstone, ledge and veneer sizes a shop actually buys; a fabricator splitting pieces on site to fine-tune thickness is doing the same operation at a smaller scale, working with the grain rather than against it.

Sawing comes in wherever the job needs a straight edge, a square corner, or a dimension the quarry's natural splitting will not deliver - squaring a flagstone for a cut-stone walkway, trimming ledge veneer to fit a corner, or cutting a tread or cap to length. Because quartzite is essentially pure, interlocked quartz, it is hard and highly abrasive to cut; a diamond blade and segment matched to hard, high-silica stone, run wet wherever possible, performs far better than a blade intended for softer limestone or marble, and any dry cutting or grinding needs the same silica dust controls fabricators already use on granite and engineered quartz (OSHA's respirable crystalline silica standard sets a permissible exposure limit of 50 micrograms per cubic meter as an 8-hour time-weighted average, with an action level of 25 micrograms per cubic meter).

Drilling and Shaping

Holes for post caps, light fixtures, hardware anchors or drainage in a cut-stone cap are drilled with diamond core bits the same way they would be in granite, again wet whenever the setup allows it. Because the stone's mica partings run through the thickness of a piece, a core bit entering near the edge of a plate can walk toward the nearest parting instead of drilling straight down; starting the hole slowly and keeping it well inside the piece's margin avoids losing a corner. Treads, caps and sills that need a flat, safe walking surface are commonly finished with a sawn and lightly honed top while the vertical face and underside are left on the natural split - the combination gives a tread that still reads as a cleaved stone from the side while behaving like a cut stone underfoot.

Setting It Without Losing the Bond

A freshly split mica face sheds fine flakes more readily than a sawn granite or limestone face, and those loose flakes sit exactly where a mason needs a thinset or mortar bond to grab. Brushing or blowing the back of each piece clean of dust and loose mica immediately before back-buttering, rather than relying on surface moisture alone to carry the bond, is standard practice among installers working this stone. For exterior flagstone joints and veneer, a polymer-modified or Type S mortar is the common recommendation over a straight Type N mix, because the added flexibility and bond strength tolerate the stone's own thermal movement and the uneven thickness that comes with hand-split material better than a leaner mix does.

Product Form Typical Thickness How It Is Cut Where It Is Used
Flagstone (e.g. E-Z Set type) About 3/8 to 5/8 in. Split thin, edges sawn to size as needed Pre-cast hearths, thin paving, thin veneer
Ledge/building veneer About 1-1/2 to 3 in. (some pieces thicker) Hand split, chiseled to length Exterior wall veneer, fireplace surrounds
Sawn thin veneer About 3/4 to 1-1/4 in. Full-bed stone sawn down to a calibrated depth Lightweight veneer where a flat back is required
Sawn-top treads and caps Cut to order, varies by job Split face and underside, sawn and honed top Steps, wall caps, sills

Pro Tip: Order ten to fifteen percent over your measured area before you start a flagstone or ledge job in Oakley stone, and order it by the named color grade, not just by the species name - natural splitting yields a range of thicknesses and breakage that a calibrated sawn slab never does, and a mixed-grade pallet is much harder to fix after the wall is half built than before you place the order.

Trade-Specific Tips for Larger Runs

On a production run - a hundred linear feet of veneer or a full patio - sorting pays for itself before the first piece is set. Spreading several pallets out and pulling pieces by color and thickness into separate stacks, the way a mason would with any irregular flagstone, lets the crew build a visually even field instead of discovering the clash of a warm honey piece next to a cool silver one after the mortar has set. Because Oakley stone's grading is done by hand at the quarry and again, informally, on site, two pallets of the same named grade can still differ enough that a side-by-side check before setting is worth the time it takes.

Blade selection matters more on this stone than on a softer sedimentary flagstone. Quartzite's hardness and its essentially 100-percent silica composition make it considerably more abrasive to a diamond blade than limestone or sandstone, so a segment bond intended for soft stone will glaze over and stop cutting long before the job is done. A blade matched to granite or hard, abrasive stone, with adequate water to the cut, holds its edge and keeps dust down at the same time - the two goals run together on this material rather than trading off against each other.

Waste planning on a hand-split material is different from waste planning on a calibrated slab. A plate that looks usable at the quarry can still break along a hidden mica plane the moment it is lifted or struck, and the resulting loss is not a fixed percentage the way kerf loss on a saw cut is - it depends on the particular pallet, the grade, and how carefully the crew handles the stone between the truck and the wall. Building in a generous overage and expecting some pieces to break down into smaller ledge or accent pieces, rather than treating every break as scrap, keeps a job on schedule without forcing a second order mid-project.

Oakley stone is frequently specified alongside other regional flagstones on the same property - a patio in one material next to a retaining wall or accent band in another - and matching joint width, mortar color and edge treatment across two different stones is a detailing decision worth making at the design stage rather than discovering a mismatch after both materials are delivered. Treating the stone's own color grades as the first variable to lock down, before worrying about how it will sit next to a second species, avoids re-ordering work later.

Maintenance and Long-Term Behavior

Quartzite as a rock class is known for very low porosity and water absorption compared with most building stones, because the metamorphic process that forms it fuses the quartz grains into an interlocking mass with few open pores left for water to enter. That generally supports good freeze-thaw performance outdoors in a cold climate like Idaho's or the northern United States generally, but absorption and porosity are not published figures for Oakley stone specifically, and they can vary from one quarry pit or even one pallet to the next, so a water-bead test on a sample piece is still the most reliable way to judge a given lot before committing to an unsealed exterior installation.

Because the stone is quartz-dominant rather than calcite-based, it is not acid-sensitive the way marble, limestone or travertine are; typical household and masonry cleaners will not etch it the way they would a calcite stone. That does not make it stain-proof - a mica-rich split face can still pick up oil, rust from steel fasteners or algae in a shaded, damp location - and a quartzite-rated impregnating sealer such as Akemi Transformer MAX is a common choice where a client wants stain resistance on an exterior patio or entry without changing the stone's natural look.

Routine cleaning is simple: a pH-neutral cleaner and a stiff brush handle most dirt and biological growth on an exterior installation, while anything acidic is best avoided less because it will etch the stone and more because it can still attack mortar joints and any nearby metal hardware. On an interior hearth or accent wall, dusting and an occasional damp wipe is usually all a split or honed Oakley stone surface needs, since the stone sees none of the grease or foot traffic a kitchen or entry floor would.

Long-term, the main failure mode on this stone in the field is not the quartzite itself giving out but the joint or the bond around it - a mortar joint that was never matched to the stone's movement, or a thinset applied over mica dust that was never brushed away. Reworking a failed joint on a wall built from this stone is no different from any other flagstone or veneer repair: cut out the failed mortar, clean both faces back to sound material, and rebed with a mortar suited to exterior exposure, checking that the replacement piece is pulled from the same color grade as its neighbors.

Two other American quartzitic building stones are worth comparing before specifying Oakley stone on a job: Crab Orchard stone from Tennessee is a quartzitic sandstone with its own distinct buff-and-brown palette and a different splitting behavior, and Vermont slate is a true slate that cleaves far more uniformly thin than quartzite ever will; both make useful points of comparison rather than substitutes. For the broader question of laying any irregular flagstone, cut or natural, the flagstone patio installation guide covers joint patterns and base preparation that apply whether the material on the pallet is Oakley stone or something else entirely.

Free Tool

Stone ID — not sure whether a sample on your bench is a true quartzite, a dolomitic marble sold as "quartzite," or something else entirely? Answer a few questions about color, hardness and surface feel and get a working identification plus what the stone is good for.

Identify a Stone →

Stock Up for Your Next Flagstone or Veneer Job

From diamond blades rated for hard, abrasive stone to core bits and quartzite-ready sealers, get the tooling this job needs in one order.

Shop Diamond Blades →
Previous Next

Leave a comment

Please note: comments must be approved before they are published.