Description
Description
Akemi Match Bond 1155 White Linen — Pre-Pigmented Cartridge Adhesive (250 mL)
AKEMI® Match Bond (Colour Bond CC) is a pre-colored, gel-like two-component adhesive that produces strong, near-invisible seams in engineered and natural stone. This cartridge is factory-pigmented in shade 1155 “White Linen” to blend into matching light stone, so the glue line disappears. Dispensed straight from a 250 mL cartridge through a static mixer nozzle, it has high bonding power, very fast surface drying, and a non-sag gel body that holds on vertical joints. AKEMI offers this adhesive in an extensive color-match range keyed to leading engineered-stone brands.
- Pre-pigmented “White Linen” (1155) — ready-matched for invisible seams
- Two-component cartridge — dispensed through a static mixer nozzle
- High bonding power with very fast surface drying
- Gel-like & non-sag — holds on vertical joints
- For engineered & natural stone; resistant to water, petrol, and mineral oils
| Property | Detail |
|---|---|
| Brand | Akemi |
| Manufacturer | AKEMI GmbH, Nuremberg, Germany |
| Product Type | Pre-colored, two-component cartridge adhesive (Colour Bond CC) |
| Chemical Basis | Two-component epoxy-acrylate |
| Consistency | Gel-like, non-sag |
| Color | White Linen (color code 1155) |
| Mixing Ratio | 10 : 1 (via static mixer nozzle) |
| Working Time | Approx. 5–7 minutes at 68°F (20°C) |
| Temperature Resistance | Good adhesion up to 140–158°F (60–70°C); briefly higher under low strain |
| Resistance | Resistant to water, petrol, and mineral oils |
| Cartridge Size | 250 mL |
| Color Range | Over 50 colors matched to leading engineered-stone brands |
- Pre-colored to shade 1155 “White Linen” for near-invisible seams
- High bonding power with very fast surface drying and easy processability
- Gel-like, non-sag body holds position on vertical joints
- Good adhesion on engineered stone as well as natural and artificial stone, even at elevated temperatures
- Resistant to water, petrol, and mineral oils
- Part of an extensive color-match system for stone fabrication
Producing strong, color-matched, near-invisible joints and seams in engineered stone (engineered marble and quartz) as well as natural and artificial stone. Ideal for countertop seaming, edge build-ups, and repairs where the glue line should blend into light stone.
Choose the color code that matches the stone; AKEMI publishes recommended codes by material and brand.
- Make sure the surfaces to be bonded are clean, dry, and free of grease and dust.
- Fit the cartridge in a suitable dispensing gun and attach a fresh static mixer nozzle; the adhesive mixes at a 10 : 1 ratio as it is dispensed.
- Dispense a little to purge until the color is uniform, then apply to the joint.
- Assemble the parts and support the joint. The adhesive stays workable for approx. 5–7 minutes at 68°F (20°C); warmth shortens and cold lengthens this time.
- Remove excess before it sets. Once cured, seams can be worked flush.
- Reactive two-component adhesive with a strong odor — use only with good ventilation.
- Keep away from heat, sparks, and open flame; avoid skin and eye contact.
- Use a fresh static mixer nozzle for each cartridge to ensure correct mixing.
- Industrial chemical product — wear chemical-resistant gloves and eye protection. Always consult the AKEMI Safety Data Sheet (SDS) before use.
Industrial two-component adhesive. Keep away from ignition sources and use only in well-ventilated areas. Wear chemical-resistant gloves and eye protection. Consult the AKEMI Safety Data Sheet (available from the manufacturer or stein.akemi.de) before use. Technical values are manufacturer figures at 68°F (20°C) and may vary with jobsite conditions.
