Large holes get the attention in porcelain work. Sink cutouts, faucet holes and cooktop openings are planned, measured and checked twice. The small holes are a different story: a pilot for a soap dispenser, a pair of holes for a towel bar, an anchor point for a bracket, a clearance hole for a fastener in a backsplash. They are quick jobs that often get handed to whichever bit is closest, and that is exactly when a porcelain panel or tile chips at the edge, cracks from heat or ends up with a hole that wandered off the mark. Small holes in brittle material deserve the right bit too.
This spotlight looks at the Weha Weramic Non-Core Diamond Drill Bit for Ceramic Porcelain Small Holes, part of Weha's Weramic family of bits for porcelain and ceramic. Our listing offers it in 3/16", 1/4" and 5/16" diameters on a 5/8-11 connection, with a recommended speed of 1600 to 2800 RPM, adjusted for size and material. Below we cover what the bit is designed for according to Weha and its distributor, how to set it up for clean holes, the technique that keeps porcelain from chipping, which materials it is not meant for, and how to care for it so it keeps drilling cleanly.

Why Porcelain Punishes the Wrong Bit, and Where the Weramic Fits
Porcelain is defined by how little water it absorbs. Under ANSI A137.1, porcelain tile is ceramic tile with a water absorption of 0.5% or less when tested to ASTM C373, and industry sources describe water absorption as the deciding factor for whether a tile can be called porcelain. That low absorption comes from a dense, highly vitrified body. For a fabricator or installer, dense means hard to cut and quick to heat up under a drill, while the glassy surface means chips and spalls show immediately. A bit that would be fine in soft wall tile can struggle in a porcelain panel.
Weha positions the Weramic line for exactly these materials. Trade coverage of the Weramic launch describes a thin-wall design with only a 2 mm rim, intended to drill smooth, chip-free holes in material from 6 mm to 30 mm thick, with a 5/8-11 version suited to ceramic products such as floor and wall tile and a CNC version for large porcelain panels and sintered stone. The distributor page for this specific non-core bit, linked from our listing, repeats the 2 mm thin-wall rim and the 6 mm to 30 mm thickness range and lists large-format porcelain panels, sintered materials and ceramic floor and wall tile as compatible.
Our product description summarizes the same idea in plain terms: professional blind hole bits for stone fabrication, an ultra-thin rim for faster drilling, and clean, chip-free holes in brittle materials. A thin rim removes less material than a thick one, so the bit has less to grind away on every revolution. That is where the speed comes from, and it is also why a thin-rim bit tends to leave a cleaner edge: less material is being fractured at the surface. The trade-off is that a thin rim needs to be kept cool and fed gently, which shapes everything about how this bit should be used.
Weha's distributor also says clearly what the bit is not for. The page lists engineered stone, quartz and quartz agglomerate as materials not to drill with this bit. That matters because many shops handle porcelain and engineered quartz side by side. Engineered stone needs diamond tooling rated for engineered stone, so keep a separate bit for quartz work and do not assume that a porcelain bit will cross over. For larger porcelain holes, the same family includes Weramic porcelain ceramic core bits with a 5/8-11 thread, which trade coverage lists from 1/2" up to 3-1/2".
Setting Up and Drilling Clean Small Holes
Start with the tool. According to the distributor page, the bit fits standard 5/8-11 grinders and drills, and our listing gives the recommended speed as 1600 to 2800 RPM, adjusted for size and material. Check the no-load speed of the tool you plan to use, because a tool running faster than the recommended range works against you; a variable-speed tool that can be held inside the window is the safer choice. Staying in the recommended range keeps heat under control and gives the diamonds time to cut rather than polish the surface. The distributor page lists an overall length of about 3-1/8" and a maximum drilling depth of about 1-7/8".
Choosing the right diameter
The three sizes on our listing, 3/16", 1/4" and 5/16", cover the small holes that come up most often around a finished installation. The distributor lists typical applications as faucet and plumbing holes, anchor and hardware installs, jobsite modifications and shop fabrication. Match the bit to the fastener or anchor manufacturer's recommended hole size rather than guessing, and drill a test hole in an offcut of the same material when you can. A hole that is slightly too small in porcelain cannot be forced open by the anchor without risk of cracking, while one that is too large weakens the hold.
| Detail | What the product data and Weha distributor list |
|---|---|
| Diameters | 3/16", 1/4", 5/16" |
| Connection | 5/8-11 thread; fits standard 5/8-11 grinders and drills |
| Recommended speed | 1600 to 2800 RPM, adjusted for size and material |
| Rim | Ultra-thin (2 mm thin-wall rim per distributor page) |
| Material thickness | 6 mm to 30 mm with proper drilling technique |
| Compatible materials | Large-format porcelain panels, sintered materials, ceramic floor and wall tile |
| Not intended for | Engineered stone, quartz, quartz agglomerate |
| Approximate size | About 3-1/8" overall length, about 1-7/8" max drilling depth |
| Manufacturer part numbers | 142853, 142857 |
Marking, starting and holding position
Mark the hole on masking tape rather than directly on the glaze. Both home-improvement and trade guides recommend tape over the drilling spot because it helps keep the bit from slipping on a smooth surface and gives you a visible mark to hold. Start slowly with light pressure, aligned with the mark, and let the diamonds establish a shallow groove before you build speed. Once the bit has bitten in, increase pressure gradually and keep it steady. Wandering is the most common cause of ruined small holes, and a careful start solves most of it before it begins.
Water and pressure through the cut
Keep the cut wet. The distributor page for this bit states that the material should not be processed dry and recommends wet use, with wet cleanup methods and proper protective equipment. General tile-drilling guidance agrees that spraying water on the bit and tile when drilling porcelain helps avoid overheating, controls dust and reduces the risk of cracking. A spray bottle, a small dam of plumber's putty around the mark, or a helper with a water line all work. Let the drill do the work with steady, gentle force rather than leaning on it, since excess pressure on a thin rim builds heat quickly.
Ease off as you approach breakthrough. Guides from both trade and retail sources advise reducing pressure when the bit nears the back of the tile, because that is when the underside is most likely to blow out and chip. On a panel that is already installed, the back face may be supported by setting material, but on a loose piece or an overhang, the underside is unsupported. Clamping the piece to a flat surface, or backing it with a sacrificial board where practical, helps. After breakthrough, clear the slurry and inspect the edge before moving on to the next hole.
Spotlight: The Weha Weramic non-core bit combines an ultra-thin rim with a 5/8-11 connection, so the same grinder or drill you already use for larger 5/8-11 core bits can handle 3/16" to 5/16" holes in porcelain and ceramic. Keep it inside the 1600 to 2800 RPM window, keep water on the cut as the distributor instructs, and save it for porcelain, ceramic and sintered materials. For engineered quartz, switch to a bit rated for engineered stone.
Advanced Tips for Fabricators and Installers
In the shop, small holes are usually drilled before installation, which gives you control. Lay the piece flat on a padded, level table, mark on the finished face and drill from that face, so the edge you will see is the one you control from the start. Group holes by diameter so you change bits as few times as possible, and keep each Weramic size in a labeled holder. If a job calls for several holes in a row, such as hardware rails or a series of anchor points, drill a test hole in an offcut of the same panel first to confirm speed and feed before touching the finished piece.
On the jobsite, conditions are less forgiving. The panel may already be set, water has to be contained, and the operator is often working at an awkward angle on a wall. A cordless or corded drill with a 5/8-11 adapter that can be held in the speed range is easier to control than a full-size grinder in tight spaces. Protect surrounding finishes from slurry, keep a towel and a sponge within reach, and work in short intervals so heat does not build. If the hole will receive an anchor, vacuum or rinse the dust out before setting it so the anchor seats properly.
Dust control applies even to small holes. Drilling porcelain, ceramic and stone can generate respirable crystalline silica, and OSHA's permissible exposure limit is 50 micrograms per cubic meter of air as an 8-hour time-weighted average, with an action level of 25 micrograms per cubic meter. Wet drilling, as the distributor recommends for this bit, is one of the most practical ways to keep dust down, and the same page calls for wet cleanup rather than dry sweeping. Safety glasses, hearing protection and respiratory protection appropriate to the exposure belong on every drilling job, regardless of how small the hole is.
Large-format porcelain and sintered panels raise one more consideration: thickness. Weha's distributor lists the bit's working range as 6 mm to 30 mm, which covers the common thin tile and panel formats as well as many thicker countertop slabs, and the listed maximum drilling depth is about 1-7/8". Check the material thickness on the job before drilling, especially on laminated or mitered edges where the effective thickness can double. If a hole needs to pass through a build-up, confirm the depth will be reached in one pass rather than forcing the bit beyond its design.
Caring for Small Diamond Bits Over the Long Term
Small bits wear in ways that are easy to miss. After each job, rinse the bit to remove slurry, dry the thread and store it where the rim cannot be knocked against other tools. A rim that has been chipped or bent will cut unevenly, wander on the start and chip the glaze. Inspect the diamond section before each use, and if the bit is cutting slowly at the correct speed with plenty of water, set it aside and check it rather than pushing on. Never try to speed up a slow bit by adding pressure, which only adds heat.
Heat is the main enemy of diamond bits and of porcelain alike. Tile-drilling guides consistently tie overheating to cracked tiles, which is why they call for water on the bit throughout the cut. If cutting slows or the water stops flowing freely, stop, let the bit cool, and check speed and water supply before continuing. Running a thin-rim bit dry, even briefly, is the quickest way to shorten its life, which is one more reason the distributor's instruction not to process the material dry should be followed on every hole, including the quick ones.
Thread care keeps the bit running true. The 5/8-11 connection should be clean and free of slurry before mounting, and the bit should seat fully against the spindle or adapter. A bit that is not seated squarely will wobble, and wobble on a small diameter in porcelain almost always means a chipped edge. Check adapters and spindle threads for damage periodically, and replace any adapter that no longer seats flush. When several people share bits, a simple check-in, check-out habit for small diamond tools helps the shop notice when a bit has been abused.
Finally, track how the bits perform. Note roughly how many holes each size has drilled, in which materials, and when performance dropped. Over a few months, that record tells you how many spares to stock, which sizes wear fastest and whether problems trace back to technique or to the tool. It also helps you separate porcelain work from engineered-stone work, since Weha's distributor lists quartz and engineered stone as materials this bit is not designed for. A small amount of record-keeping turns small bits from an afterthought into a predictable, budgeted consumable.
Building Your Small-Hole Drilling Kit
For porcelain and ceramic small holes, start with the Weha Weramic non-core drill bit in the sizes your hardware calls for, then add larger holes with the Weramic 5/8-11 core bits. Browse our full blind hole bits collection for other small-diameter options, look through thin-wall core bits for larger porcelain openings, and see the complete Weha range for related fabrication tools.
Free Tool
Diamond Blade Selector — Answer a few questions about your material and equipment, and the selector points you to diamond tooling that matches, helping you pair porcelain bits like the Weramic with the right blades for the rest of the job.
Try the Blade Selector →Drill Porcelain Without the Chips
Find blind hole and small-diameter diamond bits sized for porcelain, ceramic and sintered surfaces.
Shop Blind Hole Bits →