Same-Day Shipping Before 12 PM ET | Call 703-957-4544

Check out our brands. MAXAW, KRATOS, RAX and more. Learn more

Stonify, our Official Tech Partner for Fabricators. Book a free demo

Lannon Stone: Working Wisconsin's Dolomitic Limestone

Lannon Stone: Working Wisconsin's Dolomitic Limestone

Dynamic Stone Tools

Lannon stone is a buff-to-gray building stone quarried around the village of Lannon in Waukesha County, Wisconsin, and it has been going into Milwaukee-area houses, churches, and bridges since the middle of the nineteenth century. Trade and homeowner conversation calls it limestone almost as often as dolomite, and both labels have some truth in them: it is a dolostone, a sedimentary rock that started life as limestone and had much of its calcium replaced by magnesium over geologic time, which is a distinction worth knowing before a fabricator picks a cleaning chemical or a setting bed for it.

This guide treats Lannon stone as working material rather than a history footnote: what it is geologically, how the quarrying industry around it grew and changed, the product forms it still ships in today, and the fabrication and installation habits that keep a dolostone performing well outdoors for decades. It closes with a quick comparison against two other dolomitic or dolomite-adjacent building stones already covered on this blog, Kasota stone and Cottonwood limestone, so a shop weighing options on a restoration or landscape job has a fast reference.

The geology behind the name

Lannon stone is a fine-grained, slabby dolostone of Silurian age, part of the same carbonate sequence that forms the Niagara Escarpment, the long limestone-and-dolomite ridge that runs from Niagara Falls through southern Ontario and into the western Great Lakes before surfacing again in southeastern Wisconsin. The caprock of that escarpment is a dolomitic limestone, commonly called dolostone, that formed when magnesium progressively substituted for some of the calcium in an older limestone bed during the Silurian period, hardening the rock and making it more resistant to erosion than the softer shale beneath it. In Waukesha County, geologists have also mapped this carbonate package as the Waukesha Dolomite, a formation of the same Silurian age quarried under local names including Lannon stone.

The practical upshot for a fabricator is that Lannon stone behaves like a dense, fine-grained limestone on tooling and finishing, not like a hard igneous stone, but it carries dolomite's somewhat better resistance to weathering and water movement than a purer calcitic limestone. Dolomite the mineral sits at roughly 3.5 to 4 on the Mohs scale, softer than a granite's quartz and feldspar but tougher than many softer marbles, which is consistent with Lannon stone's long record as an exterior building and paving material in a freeze-thaw climate.

The name itself comes from William Lannon, an Irish settler who arrived in the area in the 1840s; he was not himself a quarryman, but stone was pulled from his land early on and the community that grew up around the quarrying industry took his name. The first recorded building use dates to the late 1840s, and by 1855 at least a dozen separate quarries in the area were shipping stone by wagon into Milwaukee, mostly for paving blocks and curbing at that stage rather than finished building veneer.

The limestone-versus-dolomite confusion around Lannon stone is common enough that it is worth a plain explanation rather than picking a side. All dolomite started out as ordinary limestone, built from the shells and skeletons of marine organisms as calcium carbonate; dolomitization is the later process, still debated in some of its details among geologists, by which magnesium-rich water moving through the rock swaps some of that calcium for magnesium and converts calcite to the mineral dolomite. The result is technically a dolostone rather than a limestone, but because the transformation happened gradually and the rock still reads, looks, and quarries much like a dense limestone, trade usage calling it "Lannon limestone" persists alongside the more precise "Lannon dolomite" or "dolostone." A fabricator does not need to settle the terminology argument, but should use "dolostone" or "dolomitic limestone" on a spec sheet rather than a plain "limestone," since the two can behave slightly differently with certain masonry cleaners and setting materials.

From paving stone to a regional building material

The Lannon quarrying district grew quickly through the second half of the nineteenth century. By the early 1890s, roughly fourteen quarries were operating in the area producing stone for paving, curbing, flagging, and general building use, and the industry reached its busiest stretch between about 1880 and 1900 as Milwaukee and the surrounding towns expanded. Some of the larger operators, including the Halquist family, who started with a small curbing quarry near Sussex in 1929 and grew it into one of the state's largest stone companies, shifted the business over the twentieth century away from paving blocks and toward the decorative veneer and landscape stone that still carries the Lannon name today.

What ships under the Lannon name now

Modern Lannon stone is sold mainly as building and landscape stone rather than structural block. Current producers list it as full-bed stone veneer and as thinner sawn veneer for a lighter-weight application over an existing wall, as handcut material set in random ashlar patterns, and as steps, treads, and coping for outdoor work, alongside general landscape slabs. Post-war residential building in Milwaukee and Waukesha leaned heavily on Lannon stone for house fronts and chimneys, which is why so much of today's restoration and addition work on older Wisconsin houses still has to match it.

Sawing, splitting, and setting dolostone

Because Lannon stone is a sedimentary rock with natural bedding planes, it tends to split cleanly along those planes with a hand set or a splitting hammer, which is exactly how traditional ashlar and flagstone pieces were produced before diamond saws became standard. A diamond blade cuts it cleanly across the bedding where a straight, sawn face is wanted, and dolostone's moderate hardness is easy on blade wear compared with a hard granite or quartzite. For setting, mortar remains the traditional method for veneer and ashlar work on a masonry wall, while thin sawn veneer over an existing substrate is more often set with a polymer-modified mortar or a construction adhesive rated for the panel weight and the substrate; either way, the stone's porosity means the setting bed and any flashing details have to manage water the same way they would for any absorptive natural stone.

Landscape and hardscape work is where a large share of current Lannon stone volume goes, rather than new house construction. Steps, treads, coping, and irregular landscape slabs sawn or split from the same quarry stock as the building veneer are sold for patios, retaining-wall caps, and garden walls, and the same dolostone that has carried Milwaukee foot traffic on paving blocks since the 1850s continues to hold up well under similar outdoor wear today. A fabricator setting treads or coping should dry-lay the pieces and check for consistent thickness along a run before committing mortar, since hand-split stock from a sedimentary bed is naturally more variable in thickness than a sawn slab.

Lannon stone next to its dolomitic neighbors

Lannon is not the only dolomitic building stone with its own guide on this blog. The table below is a quick index to two others, Kasota stone and Cottonwood limestone, rather than a restatement of what those guides cover.

Stone What it is, per its own guide Guide
Lannon stone Buff/gray Silurian dolostone from Waukesha County, Wisconsin (this guide) —
Kasota stone Minnesota's golden dolomitic limestone, covered in its own working guide Kasota stone guide
Cottonwood limestone Kansas's Flint Hills building stone, covered in its own working guide Cottonwood limestone guide

Pro Tip: On a restoration or addition job, split a test piece along its natural bedding before you commit a full order — the way the fracture runs tells you how clean the ashlar faces on that particular block will come out, and it is a faster check than guessing from the quarry photo alone.

Advanced notes for restoration and exterior work

Matching old Lannon stone on a restoration job is harder than matching most quarried materials because so much of the historic stock came from dozens of small, independent quarries operating over more than a century, each pulling from a slightly different bed with its own buff-to-gray color range and grain. A sample pulled from a current producer's stock should be checked against the existing wall in direct sunlight, not under shop lighting, before an order is placed, since dolostone's color can shift noticeably between lighting conditions in a way a fabricator used to polished granite may not expect.

Cleaning old or new Lannon stone has one hard rule that differs from most tooling conversations on this blog: no acidic cleaners. Dolomite, like calcite in marble and limestone, is a carbonate mineral that reacts with acid, so a muriatic-acid-based masonry cleaner or an acidic efflorescence remover used on brick nearby can etch and dull a dolostone face on contact. A pH-neutral masonry or stone cleaner, and mechanical cleaning methods rather than chemical ones for stubborn residue, are the safer route on both historic and new Lannon work.

Efflorescence, the white powdery salt deposit that sometimes appears on damp masonry, shows up on Lannon stone walls the same way it does on brick or concrete: it is water moving through the wall carrying dissolved salts to the surface, where they crystallize as the water evaporates. It is cosmetic rather than structural in most cases, but a fabricator or mason seeing it repeatedly on a new installation should treat it as a sign to check flashing, drainage, and grout joints rather than simply brushing the salts off and moving on.

Dry-cutting or grinding any dolostone, including Lannon stone, releases fine respirable crystalline silica dust along with the carbonate dust, and OSHA's exposure limit for respirable crystalline silica is 50 micrograms per cubic meter as an 8-hour time-weighted average, with an action level of 25 micrograms per cubic meter. Wet-cutting the stone or using a vacuum-shrouded grinder keeps a fabrication bay well under that limit and is the standard practice for sawing and splitting this material in volume.

Long-term performance and upkeep

Lannon stone's long service record on Milwaukee-area houses and public buildings, much of it now well over a century old, is itself the best evidence for how it performs outdoors in a Wisconsin freeze-thaw climate: the dolomite content gives it enough resistance to water movement and frost cycling that it has remained a standard veneer and landscape stone for the region rather than a historical curiosity. That performance depends on the same water-management details that matter for any absorptive sedimentary stone: properly flashed sills and copings, mortar joints maintained rather than left to crack and open, and grading that keeps standing water away from the base of a wall.

Sealing Lannon stone is a lighter-touch conversation than sealing a polished interior granite or marble. Because most current Lannon applications are exterior veneer, steps, or landscape stone rather than a food-prep surface, a breathable water-repellent sealer rated for dolomitic limestone is the more common choice than a tight impregnating sealer, since trapping moisture behind a non-breathable coating on an exterior wall risks the kind of freeze damage the stone's natural porosity would otherwise shed.

Routine upkeep is mostly about joints and drainage rather than the stone face itself. Repointing mortar joints before they fail completely, keeping gutters and downspouts directing water away from stone veneer rather than sheeting down the wall face, and avoiding deicing salts directly against stone steps and copings all extend the service life of a Lannon installation considerably beyond what the stone alone would deliver if those details were ignored.

For a shop quarrying, splitting, or sawing this material regularly, the diamond blades collection covers the saw blades suited to sawn dolostone work, and the sealers collection includes the water-repellent and penetrating options appropriate for an absorptive exterior stone like this one. Where the Kasota stone and Cottonwood limestone guides each cover their own region's dolomitic or limestone building material, this guide is specifically about Lannon stone's Wisconsin quarrying history, its Niagara Escarpment geology, and the restoration-matching and no-acid-cleaning habits particular to working it.

Free Tool

Stone ID — not sure whether a weathered block on a restoration job is Lannon stone, a related Wisconsin dolostone, or something else entirely? Answer a few questions about color, bedding, and texture and get a working identification plus the properties that affect fabrication.

Identify a Stone →

Stock up for your next dolostone job

Blades and sealers suited to sawing, splitting, and protecting a dense sedimentary stone like Lannon are a click away.

Shop Diamond Blades →
Previous Next

Leave a comment

Please note: comments must be approved before they are published.